DeskCNC Controller Board


Page 1 of 6 1234 ... LastLast
Threads 1 to 20 of 120

Forum: DeskCNC Controller Board

Discuss DeskCNC Controller Boards and the software that controls it here.

  1. Need Help!- 5v is flashing

    Started by scheelman‎, Yesterday 04:46 AM
    flashing, klik, steppers, turn, video
    • Replies: 1
    • Views: 84
    Yesterday, 08:32 AM Go to last post
  2. Need Help!- Auto Z probe work in mach3 setup problems

    Started by scheelman‎, 12-10-2018 04:59 AM
    auto, mach3, probe, setup, work
    • Replies: 3
    • Views: 121
    12-11-2018, 12:24 PM Go to last post
  3. Biesse Rover B wrt error

    Started by tomkellner‎, 11-12-2018 04:43 PM
    • Replies: 0
    • Views: 63
    11-12-2018, 04:43 PM Go to last post
    • Replies: 0
    • Views: 81
    09-16-2018, 10:18 PM Go to last post
  4. Need Help!- Planin to upgrade to mach4 help

    Started by fvillar‎, 09-12-2018 02:29 PM
    board, machine, motion, nice, upgrade
    • Replies: 1
    • Views: 366
    09-12-2018, 04:04 PM Go to last post
  5. Need Help!- Db25 1205 bob

    Started by brontoo26‎, 12-26-2015 03:29 AM
    • Replies: 6
    • Views: 3,334
    09-08-2018, 04:03 AM Go to last post
  6. deskcnc info

    Started by RIADH‎, 06-26-2018 10:47 AM
    • Replies: 0
    • Views: 156
    06-26-2018, 10:47 AM Go to last post
    • Replies: 0
    • Views: 416
    05-24-2018, 01:10 PM Go to last post
  7. A axis as rotorary

    Started by gld952‎, 12-03-2017 08:37 PM
    axis, problems.then, put, rotatory, times
    • Replies: 1
    • Views: 1,275
    12-04-2017, 06:38 PM Go to last post
  8. Unhappy Problem- DeskCNC has trouble in G02/G03 Circular interpolation

    Started by ysymidi‎, 11-28-2017 12:11 PM
    circular interpolation, cnc, deskcnc, g02 g03 problem, software
    • Replies: 3
    • Views: 363
    11-29-2017, 01:45 AM Go to last post
  9. spindle relay commanded by mach3

    Started by shoke‎, 09-22-2017 11:02 AM
    command, mach3, relay, socket, spindle
    • Replies: 0
    • Views: 923
    09-22-2017, 11:02 AM Go to last post
  10. DeskCNC - Should I Deep Six it?

    Started by Cmguitar‎, 06-27-2017 12:37 AM
    • Replies: 7
    • Views: 1,395
    09-04-2017, 07:33 PM Go to last post
  11. Setting up 0,0 offset from laser crosshair

    Started by Gary-Wiant‎, 08-24-2017 10:16 PM
    • Replies: 3
    • Views: 484
    08-25-2017, 06:19 PM Go to last post
  12. DewskCNC Can't Jog To Touch off Tool

    Started by Cmguitar‎, 06-20-2017 11:47 PM
    buttons, grayed, jog, machine, window
    • Replies: 1
    • Views: 370
    06-25-2017, 01:21 AM Go to last post
  13. Help with Mach3

    Started by kgresiak‎, 06-23-2017 08:25 PM
    cnc, mach3, reset, spindle, uss
    • Replies: 0
    • Views: 314
    06-23-2017, 08:25 PM Go to last post
  14. Need Help!- Mach3

    Started by Snakips‎, 06-16-2017 07:59 AM
    3 Pages
    1 2 3
    • Replies: 24
    • Views: 1,486
    06-23-2017, 01:55 AM Go to last post
  15. Need Help!- desk cnc new stepper driver cw250

    Started by mrlttlman‎, 06-09-2017 11:43 PM
    cnc, cw250, driver, migh, stepper
    • Replies: 0
    • Views: 426
    06-09-2017, 11:43 PM Go to last post
  16. Newbie- stepper drive A3979

    Started by dobrodewed‎, 01-10-2017 06:26 PM
    correct, drive, motors, shapes, signal
    • Replies: 1
    • Views: 1,010
    04-04-2017, 12:02 AM Go to last post
  17. Need Help!- limit switch inputs on Mana ver 2.1 controller

    Started by cpe256‎, 12-28-2016 01:02 AM
    board, cnc, limit, mana, switches
    • Replies: 0
    • Views: 773
    12-28-2016, 01:02 AM Go to last post
  18. Help please

    Started by Chophead69‎, 01-14-2016 02:36 AM
    build, cnc, forum, software, steppers
    • Replies: 3
    • Views: 975
    12-21-2016, 04:42 AM Go to last post

Page 1 of 6 1234 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 8 users browsing this forum. (0 members & 8 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands