Need Help! machine tool emergency stop DMU 50 V millplus heidenhain


Results 1 to 4 of 4

Thread: machine tool emergency stop DMU 50 V millplus heidenhain

  1. #1
    Registered
    Join Date
    Jun 2007
    Location
    Sweden
    Posts
    4
    Downloads
    0
    Uploads
    0

    Default machine tool emergency stop DMU 50 V millplus heidenhain

    Have a problem with a DMU 50 V that sets the error code I05 when I press the start button. What can trigger that error code apart from the emergency stop switch , switch to the door and the switch for the windows slide in the tool magazine.
    Things that have been replaced in the security chain, door switch / lock (16A4) and the emergency stop button (S1) and start button (6SH1).
    All protective plates and doors are removed from the machine because the machine was higher than the door into the workshop, and to access and service the machine and clean it.
    Keys are in the switches for the tool magazine and the main door.
    Any suggestions on solving the problem are greatly appreciated.

    /Tobias

    Similar Threads:
    Last edited by Tobbe; 12-01-2015 at 06:08 PM.


  2. #2
    Registered
    Join Date
    Jun 2007
    Location
    Sweden
    Posts
    4
    Downloads
    0
    Uploads
    0

    Default Re: machine tool emergency stop DMU 50 V millplus heidenhain

    Update

    The machine also set an error code on start up indicating that the hand control is not responding. Turned out to be a bad connection at the hand control end. When that error was fixed the error code I05 also disappeared. Either it's a bug in the control program or it is a deliberate programming in order to make troubleshooting a little bit more challenging
    Now remains to find out why the power supply to the servo drives does not start



  3. #3
    Registered Tampio66's Avatar
    Join Date
    Apr 2017
    Location
    Helsinki
    Posts
    7
    Downloads
    0
    Uploads
    0

    Default Re: machine tool emergency stop DMU 50 V millplus heidenhain

    Hi !
    I have same machine Dmu 50V Millplus v400
    i had to make emergency stop when i was driving reference points ( to invoid collision).
    I even move axes after i release the emergency stop button and restart. Then i start driving reference points again it made Stop in Y axis ( Y04).
    NOW the Problem If i try to start it again. The 01 wont shut down and non axes wont get power. Also the cabin door wont get close.
    Also in electrical cabinet power supplay 6 leds are off / no lights.
    IF anyone have solution i would be more than pleased to know.
    Hope Tobbe will answer had so similar case. THANKS

    - - - Updated - - -

    Hi !
    I have same machine Dmu 50V Millplus v400
    i had to make emergency stop when i was driving reference points ( to invoid collision).
    I even move axes after i release the emergency stop button and restart. Then i start driving reference points again it made Stop in Y axis ( Y04).
    NOW the Problem If i try to start it again. The 01 wont shut down and non axes wont get power. Also the cabin door wont get close.
    Also in electrical cabinet power supplay 6 leds are off / no lights.
    IF anyone have solution i would be more than pleased to know.
    Hope Tobbe will answer had so similar case. THANKS



  4. #4
    Member Triggerman's Avatar
    Join Date
    Sep 2019
    Posts
    4
    Downloads
    0
    Uploads
    0

    Default Re: machine tool emergency stop DMU 50 V millplus heidenhain

    Quote Originally Posted by Tampio66 View Post
    Hi !
    I have same machine Dmu 50V Millplus v400
    i had to make emergency stop when i was driving reference points ( to invoid collision).
    I even move axes after i release the emergency stop button and restart. Then i start driving reference points again it made Stop in Y axis ( Y04).
    NOW the Problem If i try to start it again. The 01 wont shut down and non axes wont get power. Also the cabin door wont get close.
    Also in electrical cabinet power supplay 6 leds are off / no lights.
    IF anyone have solution i would be more than pleased to know.
    Hope Tobbe will answer had so similar case. THANKS

    - - - Updated - - -

    Hi !
    I have same machine Dmu 50V Millplus v400
    i had to make emergency stop when i was driving reference points ( to invoid collision).
    I even move axes after i release the emergency stop button and restart. Then i start driving reference points again it made Stop in Y axis ( Y04).
    NOW the Problem If i try to start it again. The 01 wont shut down and non axes wont get power. Also the cabin door wont get close.
    Also in electrical cabinet power supplay 6 leds are off / no lights.
    IF anyone have solution i would be more than pleased to know.
    Hope Tobbe will answer had so similar case. THANKS
    Moi.

    Ittellä on nyt sama ongelma samassa koneessa. Muistakko miten ongelma ratkes? Pystykkö ottaan yhteyttä roni.ampuja@gmail.com



  5. #5
    senthil1783's Avatar
    Join Date
    Feb 2020
    Posts
    16
    Downloads
    0
    Uploads
    0

    Default Re: machine tool emergency stop DMU 50 V millplus heidenhain

    I have worked in this same machine.

    Contact me if your problem is not solved

    akashengineering50@gmail.com



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

machine tool emergency stop DMU 50 V millplus heidenhain

machine tool emergency stop DMU 50 V millplus heidenhain

machine tool emergency stop DMU 50 V millplus heidenhain