I need technical support for Deckel FP50CC please

Results 1 to 6 of 6

Thread: I need technical support for Deckel FP50CC please

  1. #1
    Member
    Join Date
    Feb 2008
    Location
    Egypt
    Posts
    15
    Downloads
    0
    Uploads
    0

    Default I need technical support for Deckel FP50CC please

    Machine Supplier: Deckel

    Machine Type: FP50CC

    Serial Number: 2813-0234

    Machine control: Dialog 11
    I need technical support for Deckel FP50CC please-dialog11-jpgI need technical support for Deckel FP50CC please-monitor1-jpgI need technical support for Deckel FP50CC please-monitor2-jpgI need technical support for Deckel FP50CC please-panel-jpg
    The problem is as follow:



    When the system starts, the sequence of starting runs normally and then it finally gives the indicated status in attachments.

    Pushing green control ON button in the operator panel has no effect i.e. (drives not start), the machine then gives no error messages and no alarms as indicated in attachment "monitor1.jpg". But the abnormal behavior is that after the sequence of starting is finished:

    The (READY) led in the NPC card is ON whereas the (RUN) led in this card is OFF as indicated in attachment "Dialog11.jpg"
    The (CNC) led in the NSV card is OFF as indicated in attachment "Dialog11.jpg"
    Please give help to fix this problem

    Similar Threads:


  2. #2
    Member
    Join Date
    Nov 2016
    Location
    Australia
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default Re: I need technical support for Deckel FP50CC please

    Try https://www.cnczone.com/v...a-abene-mills/. There are very experienced people there.
    Note to Moderator - I hope this post does not contravene forum rules - I'm just trying to assist the OP.

    Bill



  3. #3
    Member
    Join Date
    Nov 2016
    Location
    Australia
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default Re: I need technical support for Deckel FP50CC please

    That was meant to be cnczone.com/vb/deckel-maho-aciera-abene-mills/ but it came out wrong.
    Bill



  4. #4
    Member
    Join Date
    Feb 2008
    Location
    Egypt
    Posts
    15
    Downloads
    0
    Uploads
    0

    Default Re: I need technical support for Deckel FP50CC please

    Quote Originally Posted by WCD9 View Post
    Try https://www.cnczone.com/vb/deckel-ma...a-abene-mills/. There are very experienced people there.
    Note to Moderator - I hope this post does not contravene forum rules - I'm just trying to assist the OP.

    Bill
    This website is no longer available



  5. #5
    Member
    Join Date
    Feb 2008
    Location
    Egypt
    Posts
    15
    Downloads
    0
    Uploads
    0

    Default Re: I need technical support for Deckel FP50CC please

    Praise be to Allaah
    My machine has been repairedI need technical support for Deckel FP50CC please-1-jpgI need technical support for Deckel FP50CC please-1-jpgI need technical support for Deckel FP50CC please-2-jpg



  6. #6
    Member
    Join Date
    Feb 2008
    Location
    Egypt
    Posts
    15
    Downloads
    0
    Uploads
    0

    Default Re: I need technical support for Deckel FP50CC please

    The same problem is repeated again



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

I need technical support for Deckel FP50CC please

I need technical support for Deckel FP50CC please