Package include:
1 x 4 axis USBCNC breakout board
1 x Hand controller
1 x USB Cable
CD include with English user manual and software and register code.
This is Video download address:ddcnc.com/file/usbCNCV4.rar
1. Products brief introduction
USBCNCV4.0 is a high performance motion controller which based on PC software USBCNC control, the system can complete the convers$
2. Computer system requirement
???????????????? ???????????????
1) CPU:1GHz
2) Memory: 512MB
3) 500MB free disk space
4) DIRECTX9 graphics device with WDDM 1.0 or higher driver
5) USB 2.0 interface
6) Net FRAMEWORK 3.5SP1
???????????????? ????????
1) CPU:2GHz
2) Memory: 2GB;
3) 1G free disk space
4) DIRECTX9 graphics device with WDDM 1.0 or higher driver
5) USB 2.0 interface
6) Net FRAMEWORK 3.5SP1
3.Production appearance and size
1. After the revision,V4 version using the red PCB board, PCB size is 135.3*82.5mm.;
2. The front of the narrow edge placed with USB communication interface and DB9 hand control interface for the convenience of cus$
3. The back-end of narrow edge is power input and output interface and 3 relay output interface; relay is strong interference sou$
4. One of the two wide sides is stepper motor and principal axiscontrol signal output;
5. The another side of two wide sides is the emergency stop, manual speed input, limiting input interface; one side for the input$
6. 5V and 12V power module compact independence, security, stability;
7. External ensure the stability of the system work effectively with crystal active and main control chip shield;
8. The software is USBCNC,not mach3,pls note!
4.Detailed functional introduction
A. Card input voltage: 15~36V;
B. Limit port working voltage: 12V;
C. Stepper motor control signal output voltage: 5V;
D. External power supply voltage: 12V;
Note: marked 15~36VDC is input interface, marked 12V is output interface, can not wiring wrong.
5.Function and definition of each module
A) USB interface, connect to the computer USB port through this interface,you can use the software usbcnc to control this board, this USB interface is the square B interface,please use USB2.0 connection cable which with shielding and ma$
B) Hand control box interface, external hand control box can use this interface to access the system, the interface is standard DB9 form, its definition as shown in the following table.
C) Power indicator, as shown in figure the above D10 indicator is the front-end USB power indicator, this light lit up after USB port connection with computer , D2 in below is the back -end power indicator light, this light also will li$
D) Board card firmware upgrade button UP and reset button RST, firmware has been updated, so upgrade button don?t need to use, reset button be used when need to restart due to the board fault.
E) Manual speed control interface,wiring connection mode as shown in the following figure .
F) Limit input interface. Limit interface definitions are listed in the following table in the user manual
G) Spindle control selector switch, as shown in Figure 1-6, the switch shift up to the S1 position for the spindle speed control ; switching switch position On below for output control MIST relay .
H) External pause and reset interface; the 2 feet marked PAUSE connect suspend switch, 2 feet marked RESET connection reset switch.
I) Software MIST control relay output, software settings output marked 3, defined from top to bottom, 3 feet is NC, NO, COM.
J) Software FLOOD control relay output ,output marked 2 in the software settings , defined from top to bottom, 3 feet is NC, NO, COM.
K) Software SPINDLE control relay output , output marked 1 in the software settings , defined from top to bottom, 3 feet is NC, NO, COM.
L) Board working power input, levels above negative below as the board signed, please pay attention to input DC 15~36V, overvoltage or reverse connection will damage the board.
M) 12V output interface. as the board marked, GND is -, 12V is +.
N) Spindle control output interface: definitions turn for GND DIR PWM2 12V, respectively is ground,direction signal output, spindle 0~10V speed control signal output, 12V output.
O) A axis stepper motor control signal output, the definition is:CK+CK-DIR+DIR-,respectively is impulsion positive, impulsion negative, direction positive, direction negative, the board using common anode connection method, so CK+ and D$
P) Z axis stepper motor control signal output, the definition is CK+CK-DIR+DIR-, respectively for pulse positive, pulse negative, direction positive , direction negative, the board using anode common connection method, so CK+ and DIR+ l$
Q) Y axis stepper motor control signal output, the definition is CK+CK-DIR+DIR-,respectively for pulse positive, pulse negative, direction positive , direction negative, the board using anode common connection method, so CK+ and DIR+ li$
R)X axis stepper motor control signal output, the definition is CK+CK-DIR+DIR-,respectively for pulse positive, pulse negative, direction positive , direction negative, the board using anode common connection method, so CK+ and DIR+ lin$