Controller & Computer Solutions


Page 1 of 81 12341151 ... LastLast
Threads 1 to 20 of 1604

Forum: Controller & Computer Solutions

Discuss computers and setups for cnc controllers.

    • Replies: 7
    • Views: 777
    10-23-2014, 12:59 PM Go to last post
  1. 'Best' controller/software for 2 axis lathe conversion

    Started by dbsharp‎, 09-29-2019 10:42 AM
    cnc, lathe, lunix, support, tool
    • Replies: 6
    • Views: 2,492
    10-01-2019, 09:20 PM Go to last post
  2. *Newbie* Connecting Tosnuc 888 to NCnet Lite

    Started by sethj97‎, 10-26-2023 01:25 PM
    • Replies: 1
    • Views: 341
    10-26-2023, 02:56 PM Go to last post
  3. ...Advice about Planet CNC ???

    Started by Martel‎, 10-07-2019 08:14 AM
    cnc, controller, motor, software, usb
    • Replies: 2
    • Views: 2,251
    12-20-2019, 09:01 AM Go to last post
  4. 18i upgrade from Windows 98 - 2000

    Started by C-sCnc‎, 01-03-2011 09:16 AM
    • Replies: 1
    • Views: 1,875
    01-27-2016, 06:47 PM Go to last post
  5. Need Help!- 1988 fadal 2040 with toshiba G7ASD control

    Started by dwolf‎, 08-21-2011 01:38 PM
    not
    • Replies: 0
    • Views: 1,041
    08-21-2011, 01:38 PM Go to last post
  6. 1st Post, Probably in the wrong place....

    Started by sheeter‎, 10-05-2011 05:50 PM
    • Replies: 14
    • Views: 2,431
    10-13-2011, 06:05 PM Go to last post
  7. 2 Q's 3.5a controller with 4.6a motor.

    Started by thrasherfox‎, 07-07-2011 11:12 PM
    keep, not, since, then
    • Replies: 7
    • Views: 1,398
    07-10-2011, 10:40 AM Go to last post
  8. 20 axis controller

    Started by DaveReimer‎, 03-09-2011 07:20 PM
    • Replies: 8
    • Views: 1,660
    03-12-2011, 05:45 PM Go to last post
  9. Newbie- 2001 6x12' Multicam Motion Control Retrofit?

    Started by Parkgrr‎, 09-13-2020 05:14 AM
    • Replies: 4
    • Views: 1,104
    12-01-2020, 06:50 PM Go to last post
  10. Question Need Help!- 3 "New" machines with Anilam controllers - should I change them?

    Started by ronglax‎, 03-15-2014 01:27 PM
    mos, non
    • Replies: 4
    • Views: 1,109
    03-17-2014, 12:04 PM Go to last post
  11. 3 axis cnc controller circuit help

    Started by CNCexplorer‎, 04-30-2012 11:43 AM
    another, mos, not, say
    • Replies: 0
    • Views: 846
    04-30-2012, 11:43 AM Go to last post
    • Replies: 1
    • Views: 2,349
    02-06-2009, 01:39 PM Go to last post
  12. 3 or 5 volt Opto Isolation for Printer Port

    Started by der_fisherman‎, 08-30-2009 12:23 PM
    • Replies: 4
    • Views: 3,505
    08-31-2009, 03:41 AM Go to last post
  13. 3.5" floppy to USB conversion?

    Started by Gundawg‎, 11-12-2011 12:39 PM
    307, e93, not
    • Replies: 2
    • Views: 5,187
    07-30-2012, 05:07 PM Go to last post
  14. 3020 motion controller replacement

    Started by Jdm1206‎, 08-11-2020 07:10 PM
    cnc, controller, current, motion, spindle motion controller
    • Replies: 0
    • Views: 470
    08-11-2020, 07:10 PM Go to last post
  15. Need Help!- 4 axis CNC router with tangential knife for rubber sheets cutting

    Started by alexpavl1‎, 10-19-2016 07:54 PM
    axis, cnc, forum, knife, software
    • Replies: 0
    • Views: 1,607
    10-19-2016, 07:54 PM Go to last post
  16. 4 axis tb6560 need help

    Started by casi‎, 06-23-2011 04:15 PM
    2 Pages
    1 2
    • Replies: 26
    • Views: 4,327
    07-25-2011, 11:17 AM Go to last post
  17. Question Need Help!- 4 Axis TB6560 to Mach3 Config ? ?

    Started by brutusgraphics‎, 06-28-2011 06:08 PM
    cnc., not
    • Replies: 3
    • Views: 3,036
    07-08-2011, 05:31 PM Go to last post
  18. 4 wire driver board

    Started by lancut‎, 11-28-2008 10:35 PM
    • Replies: 11
    • Views: 3,680
    11-30-2008, 11:11 AM Go to last post

Page 1 of 81 12341151 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 12 users browsing this forum. (0 members & 12 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands