Controller & Computer Solutions


Page 1 of 72 12341151 ... LastLast
Threads 1 to 20 of 1431

Forum: Controller & Computer Solutions

Discuss computers and setups for cnc controllers.

  1. Anilam 3 axis Mill Y axis Lag over Max

    Started by markems0‎, Yesterday 10:57 AM
    • Replies: 3
    • Views: 72
    Yesterday, 02:31 PM Go to last post
  2. Burny 3 will not load from serial I/O

    Started by Steelman223‎, Yesterday 12:45 PM
    checking, i/o, load, powered, serial
    • Replies: 0
    • Views: 63
    Yesterday, 12:45 PM Go to last post
  3. DSP Controller

    Started by Oldie-Biker‎, 05-03-2021 01:14 PM
    • Replies: 0
    • Views: 61
    05-03-2021, 01:14 PM Go to last post
  4. SMC5-5-N-N Chinese controller - anyone have experience with it?

    Started by blades‎, 04-02-2019 09:37 PM
    3 Pages
    1 2 3
    • Replies: 58
    • Views: 9,921
    05-03-2021, 03:57 AM Go to last post
  5. Need Help!- Y Axis loosing 20mm exactly always

    Started by Bascil‎, 05-02-2021 04:59 PM
    20mm, axis, machine, sheet, tool
    • Replies: 2
    • Views: 380
    05-03-2021, 02:13 AM Go to last post
  6. Uploading to CNC90 - How?

    Started by Chris Booth‎, 12-22-2010 06:18 AM
    2 Pages
    1 2
    • Replies: 29
    • Views: 15,127
    05-02-2021, 05:39 AM Go to last post
  7. Moved: Need Help!- I have a problem connecting the computer to the machine

    Started by Salah7701‎, 05-01-2021 08:43 PM
    •  
    •  
  8. Connecting an MPG to the SMC5

    Started by NTSOS‎, 04-22-2021 11:45 AM
    connected, db26, in1, mpg, wire
    • Replies: 1
    • Views: 363
    04-27-2021, 04:49 PM Go to last post
  9. Supermax YCM-40 AB Bandit IV controller replacement

    Started by t120s3‎, 04-26-2021 06:34 PM
    bandit, controller, mill, power, replace
    • Replies: 1
    • Views: 172
    04-27-2021, 02:14 AM Go to last post
  10. Syntec controller

    Started by Buildit247‎, 04-22-2021 06:13 PM
    controller, guru, machine, software, syntec
    • Replies: 2
    • Views: 210
    04-26-2021, 09:20 PM Go to last post
  11. Smile New Machine Build- Looking for pin assignments on SMC4-4-16A-16B

    Started by Trooble‎, 02-23-2021 07:44 PM
    cnc, forum, laptop, spindle, unit
    • Replies: 3
    • Views: 337
    04-20-2021, 09:15 AM Go to last post
  12. Moved: New Machine Build- Blog about self-made CNC machine and more

    Started by Gog0‎, 04-20-2021 08:57 AM
    •  
    •  
  13. Unhappy Newbie- SMC 4-4 Failure

    Started by Trooble‎, 03-16-2021 02:10 AM
    cnc, forum, manual, problem, spindle
    • Replies: 2
    • Views: 366
    04-11-2021, 01:37 AM Go to last post
  14. Build Thread- Tomatech TAC2005M cnc controller retrofit. SZ-GH1000MC

    Started by proto-psycho‎, 02-06-2021 10:09 PM
    • Replies: 4
    • Views: 991
    04-09-2021, 08:14 PM Go to last post
  15. New Machine Build- Controller for Bridgeport/EZ TRAK plus

    Started by rcktscientist‎, 04-09-2021 05:44 PM
    bobcad, controller, post, software, trak
    • Replies: 1
    • Views: 469
    04-09-2021, 06:59 PM Go to last post
  16. Thumbs down EMCO Turn 50 Lathe RS485 PC Board Device driver

    Started by mazda28‎, 12-10-2008 10:06 AM
    device driver, not, said
    • Replies: 9
    • Views: 6,181
    04-07-2021, 12:05 PM Go to last post
  17. Delta NC300 contoller setup master slave

    Started by nicubila‎, 04-15-2019 06:30 AM
    • Replies: 6
    • Views: 2,152
    04-05-2021, 09:31 AM Go to last post
  18. Question UPGRADE OF CNC SYSTEM TOSNUC TO FANUC

    Started by vblraj279‎, 03-25-2021 07:45 AM
    • Replies: 0
    • Views: 143
    03-25-2021, 07:45 AM Go to last post
    • Replies: 3
    • Views: 396
    03-23-2021, 09:17 AM Go to last post
  19. Need Help!- How to import planetcnc module in Python

    Started by murkoc‎, 03-23-2021 04:04 AM
    found, planetcnc, python, run, software
    • Replies: 0
    • Views: 370
    03-23-2021, 04:04 AM Go to last post

Page 1 of 72 12341151 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 7 users browsing this forum. (1 members & 6 guests)

  1. jpalley

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands