Controller & Computer Solutions


Page 1 of 61 12341151 ... LastLast
Threads 1 to 20 of 1215

Forum: Controller & Computer Solutions

Discuss computers and setups for cnc controllers.

  1. Need Help!- Guildemeister CTX 500 E Error

    Started by triaxis‎, Yesterday 10:09 PM
    controller, drive, error, servo
    • Replies: 0
    • Views: 71
    Yesterday, 10:09 PM Go to last post
  2. Need Help!- Bought machine and want/need to change controller - recommendations?

    Started by Talkiet‎, Yesterday 09:40 AM
    • Replies: 1
    • Views: 110
    Yesterday, 02:18 PM Go to last post
    • Replies: 2
    • Views: 200
    07-21-2018, 05:13 PM Go to last post
  3. New Machine Build- old machine cnc

    Started by luisjesus‎, 07-19-2018 11:36 AM
    • Replies: 3
    • Views: 189
    07-20-2018, 11:10 AM Go to last post
  4. Updating my controller... finally

    Started by Fegenbush‎, 07-18-2018 03:45 PM
    cam, controller, machine, motors, software
    • Replies: 3
    • Views: 174
    07-19-2018, 06:08 PM Go to last post
  5. Tria 7500 for Morbidelli Author 503

    Started by stoned‎, 02-02-2007 07:30 AM
    4 Pages
    1 2 3 4
    • Replies: 42
    • Views: 16,474
    07-19-2018, 02:03 AM Go to last post
  6. Need Help!- Anilam 5000M Knee Mill - Repair or upgrade\refit

    Started by WM250V‎, 07-18-2018 12:55 PM
    5000m, anilam, control, machinist, posts
    • Replies: 0
    • Views: 77
    07-18-2018, 12:55 PM Go to last post
  7. Ordered the UC400ETH

    Started by wjbzone‎, 07-11-2018 10:50 AM
    cable, cnc, ordered, software, uc400eth
    • Replies: 6
    • Views: 219
    07-12-2018, 09:02 AM Go to last post
  8. Need Help!- DDCSV chinese stand alone controller doesn't open gcode

    Started by cecco156‎, 11-27-2017 04:09 AM
    chinese, controller, ddcsv1.1, digital dream, standalone
    • Replies: 7
    • Views: 618
    07-12-2018, 07:28 AM Go to last post
  9. Angry Need Help!- Mach3 output pin only gives 0.6v

    Started by japes‎, 07-11-2018 04:30 PM
    0.6v, mach3, mach3 control, output, pin
    • Replies: 2
    • Views: 129
    07-12-2018, 04:39 AM Go to last post
  10. which breakout board to go with TB6600 drivers?

    Started by merlin777‎, 07-09-2018 06:38 PM
    board, driver, motor, stepper, tb6600
    • Replies: 2
    • Views: 154
    07-11-2018, 03:01 PM Go to last post
  11. Need Help!- Trying to figure out software options for chinese controller

    Started by dwayn‎, 05-22-2017 07:35 PM
    cnc, controller, forum, software, windows
    • Replies: 2
    • Views: 410
    07-03-2018, 06:57 PM Go to last post
  12. Problem- Anilam Crusader M no power to amps

    Started by Hythos‎, 07-01-2018 11:39 PM
    auto-mode, control, finishing, power, spare
    • Replies: 0
    • Views: 102
    07-01-2018, 11:39 PM Go to last post
  13. cnc jerk controller

    Started by rcmaniak‎, 06-20-2018 12:57 PM
    acceleration profile, cnc, controller, jerk, software
    • Replies: 1
    • Views: 267
    06-20-2018, 07:30 PM Go to last post
  14. Need Help!- Help building new machine

    Started by Chaparro1973‎, 06-17-2018 12:02 PM
    • Replies: 2
    • Views: 200
    06-18-2018, 06:55 AM Go to last post
  15. CNC Plasma Table Control

    Started by tjb1‎, 06-14-2018 11:53 AM
    cnc, mach4, supports, up/down, windows
    • Replies: 2
    • Views: 190
    06-15-2018, 12:35 AM Go to last post
  16. MB 521 not connecting to TNC 320

    Started by stttiger‎, 06-07-2018 06:13 PM
    • Replies: 0
    • Views: 128
    06-07-2018, 06:13 PM Go to last post
  17. Infimatic Freedom NC200 ????

    Started by trickeng‎, 02-05-2010 05:02 PM
    2 Pages
    1 2
    • Replies: 19
    • Views: 4,290
    06-05-2018, 04:47 PM Go to last post
  18. Question Which Electronics to Buy

    Started by drxlcarfreak‎, 11-27-2017 10:27 PM
    5 Pages
    1 2 3 4 5
    • Replies: 55
    • Views: 2,840
    06-05-2018, 09:00 AM Go to last post
  19. Need Help!- Compatible software for my machine

    Started by makaplan‎, 06-04-2018 08:38 PM
    • Replies: 0
    • Views: 145
    06-04-2018, 08:38 PM Go to last post

Page 1 of 61 12341151 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 15 users browsing this forum. (1 members & 14 guests)

  1. cncpiet

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands