Hey,
the GUI & the speed looks nice to me!
Is it a BETA release of NC PLOT Software ?
Thanks
sorry for my english.
I ask you to test my G-code editor.
Written in vb6 + OpenGL
NC-Corrector Download http://nc-corrector.inf.ua/Downloads/NC4_setup.exe
Similar Threads:
Hey,
the GUI & the speed looks nice to me!
Is it a BETA release of NC PLOT Software ?
Thanks
Available new version
Added Renumber blocks
Options renumbering in the Option/Setup/Machine/Block numbers
download link that the same
Looks nice. The Tree is good.
When I swap tasks, and back to NC4 if the cursor is not over the graphics area, it does not repaint when task window is put into focus.
Needs a redraw call for whole task when task is bought to foreground.
Super X3. 3600rpm. Sheridan 6"x24" Lathe + more. THREE ways to fix things: The RIGHT way, the OTHER way, and maybe YOUR way, which is possibly a FASTER WRONG WAY!
Are you planning it to give (sell) SOURCE CODES to some software company?
Ash
Hi,
I think your program is awesome. Runs quite smooth.
I work with Mach3 on my CNC and wondered if you were going to supply support for M codes like M98 and M99. I use it quite extensively as sometimes it's just quicker to type out some code than go the whole CADCAM route.
Thanks a million and hope it goes well from here.
What are you doing M98 and M99?
Standart is doing M98-Subprogram call, M99-Subprogram end.
This NC-Corrector understands.
Here's an example....
%
S500 M3
G54G90G0X-7.25Y-.25(START POINT OF FIRST CIRCLE TOP ROW)
G1G43H11Z.50F200.(TURN ON HEIGHT OFFSET - BRING TO .500 SAFETY PLANE)
M98P105(CALL SUBPROGRAM)
G90G0X-26.Y-.25
M98P105
G90G0X-44.75Y-.25
M98P105
G90G0X-63.5Y-.25
M98P105
G90G0X-82.25Y-.25
M98P105
G90G0X-82.25Y-19.(FIRST CIRCLE SECOND ROW)
M98P105
G90G0X-63.5Y-19.
M98P105
G90G0X-44.75Y-19.
M98P105
G90G0X-26.Y-19.
M98P105
G90G0X-7.25Y-19.
M98P105
G90G0X-7.25Y-37.75(FIRST CIRCLE THIRD ROW)
M98P105
G90G0X-26.Y-37.75
M98P105
G90G0X-44.75Y-37.75
M98P105
G90G0X-63.5Y-37.75
M98P105
G90G0X-82.25Y-37.75
M98P105
M30
O105(18 IN CIRCLES - SUBPROGRAM)
(STARTS 2" RIGHT OF TOP OF CIRCLE)
G91G1G42D1X-1.Z-1.30F200.(COMP ON - RAMP DOWN)
(Z VALUE REPRESENTS SAFETY PLANE & 3/4 BOARD & THRU CUT - .50+.75+.05=1.30)
X-1.F400.
G02J-9.(FULL CIRCLE - J VALUE DEFINES RELATIVE LOC OF CENTER POINT)
G01X-1.
G40X-1.Z1.30(COMP OFF - RAMP UP TO SAFETY PLANE)
M99(RETURN TO MAIN PROGRAM)
Hi in the small example below it seems to ignore the L5 and only performs the function once.
Using M98-M99 this way allows you to describe a profile or pocketing path and then repeat it over. Perhaps the NC Corrector uses a different syntax. I run my machine on Mach3. NC Corrector is still excellent and I'll be playing around with it much more. Thanks very much for the program.
#1=0
g00 z50
x0 y0
M98 P100 L5
m30
O100
g00 z50
x#1 y0
g00 z0
g01 z-1
y100
g00 z5
#1=[#1+100]
m99
Will in the near release..
Does this program recognizes an INCH scale? I can't make work with an inch...
Last edited by lancut; 03-13-2011 at 08:04 PM.
My 2¢
Great program, but I sometimes get a "Run-time error-11, Division by zero" error. Clicking okay causes the program to exit.
Not sure what's causing it. Some codes load fine and others don't.
Anyone else seen this before?
I'm using v4, Build 0.
This is BUG in the NC-Corrector.
Please send me your G-Code.
Thanks.
Any progress on this bug? I have the same exact error message ("Run-time error-11, Division by zero") but I can't even start the program, it crashes immediately with this error every single time. Help, please...?
"It's nice to be important but it's more important to be nice (but don't push it, ok?)"
Same version, same bug, I guess.
There is no settings.ini there at all. I guess the program never gets a chance to create it - the error on startup is practically instantaneous. I did try to copy a settings.ini from someone else's machine where the program did work, but it didn't help...
I have a suspicion this is not strictly NC-Corrector's fault, but the CodeJock component's that it seems to use: this sound curiously similar... http://www.progtown.com/topic832535-...n-by-zero.html
"It's nice to be important but it's more important to be nice (but don't push it, ok?)"
Looks great.
How many axes does it support?