Need Help! VFS5 NOT READY


Page 1 of 2 12 LastLast
Results 1 to 20 of 26

Thread: VFS5 NOT READY

  1. #1
    Member val62's Avatar
    Join Date
    Nov 2021
    Posts
    25
    Downloads
    0
    Uploads
    0

    Default VFS5 NOT READY

    When the drives are turned on, the LED on the VFS5 flashes 5 times. + - 18 volts available 10 volts available.
    MOTION LINK IN TERMINAL ERROR 83 AND 84
    1.Sabre1000 machine

    2. No wiring diagrams!

    Similar Threads:


  2. #2
    Member
    Join Date
    Mar 2011
    Location
    USA
    Posts
    460
    Downloads
    0
    Uploads
    0

    Default Re: VFS5 NOT READY

    1) if I'm remembering correctly, error 83 and 84 are typical of what I see when someone unfamiliar with Motionlink uses it and enters invalid commands so they may not be related to your issue. It is also normal to see err 14 power bus and drive powered up messages, but since it only stores the most recent codes, these may have been pushed off the list.

    2) You can get the wiring diagrams from Fives, they will want the diagram number on the serial number plate. These won't likely help much with the current VFS5 issue, but it is always better to have them when working on a machine.



  3. #3
    Member val62's Avatar
    Join Date
    Nov 2021
    Posts
    25
    Downloads
    0
    Uploads
    0

    Default Re: VFS5 NOT READY

    Can anyone help with the wiring diagram?
    My electrical cabinet number
    91203230
    Thank you!



  4. #4
    Member val62's Avatar
    Join Date
    Nov 2021
    Posts
    25
    Downloads
    0
    Uploads
    0

    Default Re: VFS5 NOT READY

    Our fan crashed on VFS5.
    vfs5 monitors the presence of a fan?
    Is it possible temporarily without a fan?



  5. #5
    Member
    Join Date
    Dec 2006
    Location
    usa
    Posts
    584
    Downloads
    0
    Uploads
    0

    Default Re: VFS5 NOT READY

    When the light flashes it is because of a bad battery, contact kilroy corporation , kilroycorp.com ???

    Mike CNC Machine Services INC | Cincinnati Milacron MachinesCNC Machine Services



  6. #6
    Member val62's Avatar
    Join Date
    Nov 2021
    Posts
    25
    Downloads
    0
    Uploads
    0

    Default Re: VFS5 NOT READY

    The LED is not blinking now.
    When all voltages are switched on:
    + 10v
    + -18v
    + 24v on c2 pin 6.9
    jumper on S7 MOTION, LIMIT
    And on PSR4 / 5
    Shines:
    sys ok
    Cpu
    FAULT
    RELAY
    AKTIV NO!
    I checked the resolver with 18om, 18om, and 36om
    On TERMINAL (Motion Link) when you enter EN (ON), appears
    ERROR 83 ...
    AND ALL

    What else can I check?



  7. #7
    Member val62's Avatar
    Join Date
    Nov 2021
    Posts
    25
    Downloads
    0
    Uploads
    0

    Default Re: VFS5 NOT READY

    now shines when voltage is applied
    ACTIV
    CPU blinking unpleasantly
    How to do autoload correctly?



  8. #8
    Member val62's Avatar
    Join Date
    Nov 2021
    Posts
    25
    Downloads
    0
    Uploads
    0

    Default Re: VFS5 NOT READY

    CPU blinks continuously



  9. #9
    Member val62's Avatar
    Join Date
    Nov 2021
    Posts
    25
    Downloads
    0
    Uploads
    0

    Default Re: VFS5 NOT READY

    ??? ????????? ?????????????



  10. #10
    Member val62's Avatar
    Join Date
    Nov 2021
    Posts
    25
    Downloads
    0
    Uploads
    0

    Default Re: VFS5 NOT READY

    It is now detected when the voltage is switched on
    ERROR 27 ”R / D JUMPERS” SEVERITY 3

    Either the jumpers on your BDS5 MC2 card are incorrectly set or the wrong
    TL has been loaded. Contact the factory.
    What to do with it?



  11. #11
    Member val62's Avatar
    Join Date
    Nov 2021
    Posts
    25
    Downloads
    0
    Uploads
    0

    Default Re: VFS5 NOT READY

    Who has a TL file on VFS5?



  12. #12
    Member val62's Avatar
    Join Date
    Nov 2021
    Posts
    25
    Downloads
    0
    Uploads
    0

    Default Re: VFS5 NOT READY

    There are instructions for creating a VFS5 spindle drive configuration?
    Or is MOTION LINK + enough !?
    Who can I ask questions?



  13. #13
    Member val62's Avatar
    Join Date
    Nov 2021
    Posts
    25
    Downloads
    0
    Uploads
    0

    Default Re: VFS5 NOT READY

    Does the forum work or not?



  14. #14
    Member val62's Avatar
    Join Date
    Nov 2021
    Posts
    25
    Downloads
    0
    Uploads
    0

    Default Re: VFS5 NOT READY

    How can I see anything from the configuration in MOTION LINK TERMINAL?
    What are the commands?



  15. #15
    Member val62's Avatar
    Join Date
    Nov 2021
    Posts
    25
    Downloads
    0
    Uploads
    0

    Default Re: VFS5 NOT READY

    Only ON, EN works in the TERMINAL.
    Other commands don't work!
    What am I doing wrong?



  16. #16
    Member
    Join Date
    Mar 2008
    Location
    United States
    Posts
    283
    Downloads
    0
    Uploads
    0

    Default Re: VFS5 NOT READY

    I think you need to have the VFS5 Drive Repaired; they will replace bad Capacitors; RTC-Clock Chip with internal Battery and reload the Spindle Program and STD variables. User Variables are setup for the particular Machine Type and Spindle Gear Ratios and MAX RPM. The Rectangular Chip on the Front Top tells them what to reload. We quote Inspect and advise 1-800-534-4750 (Fives-Cincinnati-Repair Group )



  17. #17
    Member val62's Avatar
    Join Date
    Nov 2021
    Posts
    25
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by maver1ck View Post
    1) if I'm remembering correctly, error 83 and 84 are typical of what I see when someone unfamiliar with Motionlink uses it and enters invalid commands so they may not be related to your issue. It is also normal to see err 14 power bus and drive powered up messages, but since it only stores the most recent codes, these may have been pushed off the list.

    2) You can get the wiring diagrams from Fives, they will want the diagram number on the serial number plate. These won't likely help much with the current VFS5 issue, but it is always better to have them when working on a machine.
    what are the correct commands for MOTION LINK?
    some examples please ...



  18. #18
    Member val62's Avatar
    Join Date
    Nov 2021
    Posts
    25
    Downloads
    0
    Uploads
    0

    Default Re: VFS5 NOT READY

    What commands can I use in TERMINAL?

    Attached Thumbnails Attached Thumbnails VFS5 NOT READY-terminal-jpg  


  19. #19
    Member
    Join Date
    Mar 2008
    Location
    United States
    Posts
    283
    Downloads
    0
    Uploads
    0

    Default Re: VFS5 NOT READY

    --> ERR HIST (then Enter will display your error History)
    You do not have the tools to reload the VFS5 Program and Variables.
    For Inspect and advise quote contact 1-800-534-4750 (Fives-MSI-Cincinnati-Repair-Group)
    A neat reference site is (KOLLMORGEN BDS4/5 – CNC_Principle_Repair) unsecure



  20. #20
    Member val62's Avatar
    Join Date
    Nov 2021
    Posts
    25
    Downloads
    0
    Uploads
    0

    Default Re: VFS5 NOT READY

    err 18 line 246 "EN" BAD TL
    what to do about this error?
    Is this error both hardware and software?

    Attached Thumbnails Attached Thumbnails VFS5 NOT READY-1-l-jpg  


Page 1 of 2 12 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

VFS5 NOT READY

VFS5 NOT READY