CNC 6040 connection FI MK100-2S1.5G-DK to mainboard JP-3163B cabling question - Page 2


Page 2 of 2 FirstFirst 12
Results 21 to 28 of 28

Thread: CNC 6040 connection FI MK100-2S1.5G-DK to mainboard JP-3163B cabling question

  1. #21

    Default Re: CNC 6040 connection FI MK100-2S1.5G-DK to mainboard JP-3163B cabling question

    in side the VFD, jumper and posts

    Like this..

    Attached Thumbnails Attached Thumbnails CNC 6040 connection FI  MK100-2S1.5G-DK to mainboard JP-3163B cabling question-img_0477-jpg   CNC 6040 connection FI  MK100-2S1.5G-DK to mainboard JP-3163B cabling question-img_0277-jpg   CNC 6040 connection FI  MK100-2S1.5G-DK to mainboard JP-3163B cabling question-img_0479-jpg   CNC 6040 connection FI  MK100-2S1.5G-DK to mainboard JP-3163B cabling question-img_0495-jpg  

    CNC 6040 connection FI  MK100-2S1.5G-DK to mainboard JP-3163B cabling question-img_0496-jpg  


  2. #22
    Member S3V3N's Avatar
    Join Date
    Oct 2020
    Posts
    1
    Downloads
    0
    Uploads
    0

    Default Re: CNC 6040 connection FI MK100-2S1.5G-DK to mainboard JP-3163B cabling question

    Hallo Raini,

    Ich habe exakt das gleiche Problem wie du. Ich betreibe die Maschine mehr schlecht als recht mit estlcam. Hast du das Problem gelöst
    mit dem VFD? Ich blicke hier nicht ganz durch mit der Verkabelung und diesem Zusatzteil (Converter) Wo wird der eingebaut und verkabelt?
    Kannst du mir das erklären?

    Gruss Tom



  3. #23
    Member
    Join Date
    Sep 2010
    Location
    england
    Posts
    20
    Downloads
    0
    Uploads
    0

    Default Re: CNC 6040 connection FI MK100-2S1.5G-DK to mainboard JP-3163B cabling question

    Hey there, I have this same unit which came wiht my CNC6040 i bought second hand but the VFD is locked in password mode, does anyone know the password for them?



  4. #24
    Member
    Join Date
    Jan 2005
    Location
    USA
    Posts
    11914
    Downloads
    0
    Uploads
    0

    Default Re: CNC 6040 connection FI MK100-2S1.5G-DK to mainboard JP-3163B cabling question

    Quote Originally Posted by craigrobbo View Post
    Hey there, I have this same unit which came wiht my CNC6040 i bought second hand but the VFD is locked in password mode, does anyone know the password for them?
    It will depend if someone has added a pass word but normally people should not

    This will also depend on what VFD Drive you have also

    Check Parameter PD000=0 if set to 1 that will lock parameter setting this is for the HY VFD Drive

    Mactec54


  5. #25

    Default Re: CNC 6040 connection FI MK100-2S1.5G-DK to mainboard JP-3163B cabling question

    It is a pity this topic has turned so silent as this is something a lot of users are struggling with and there is no topic with a solution or some confirming the suggestions worked.
    It contains a lot of valuable information.

    I’m also working to get the spindle speed controlled from de JP-3165B rev 3.9 board.
    I have managed to start the spindle from the CNC USB software but somehow I do not get maximum speed out of it.
    When I measure the voltage from the 0-10v pin I only measure between 5.1 and 6.1 volts. Just wondering if this is related to a setting in the old USB CNC software or it is the board.

    I’m also waiting for a parallel interface so I can do the same test with mach3 and see what I measure then, but this has to wait until I have all the components in house.

    My VFD is a bit different (A2-2015B), but essentially it can be controlled with three wires like the one discussed.
    This is how I hooked it up:
    JP-3165B - VFD
    GND -> GND
    0-10v -> 10v-in
    NO -> FWD
    C -> GND

    Last thing I want to test if this PWM to analog converter does the trick as the VFD requires analog input and from what I understand from many discussions is that the 0-10v pin on the JP-3165B issues PWM 0-10v.

    If you have some more information which might be relevant please contribute to this topic.



  6. #26

    Default Re: CNC 6040 connection FI MK100-2S1.5G-DK to mainboard JP-3163B cabling question

    Just thinking if the low voltages on the 0-10v pin could have something to to with the board being setup to use it's internal 5v instead of an external source of 12 or 24 volts.
    I don't think it is because I do get 10v on the pin in certain conditions, so it looks like the board is capable to increase the voltage
    Jumper JP1 is responsible for this. However my board is a v3.9 which has 5 jumpers instead of the 3 you commonly find on the internet.
    On these older boards you would need to place JP1 in position 2-3 and remove JP3 to allow 24v input (plus you should not forget to add resistors for the input switches!)

    Does anyone know how this is done on the newer 5 jumper boards? Does it just need JP1 in the 2-3 position and it will work with 12 or 24 volts?



  7. #27

    Default Re: CNC 6040 connection FI MK100-2S1.5G-DK to mainboard JP-3163B cabling question

    Ok, spindle control via MACH3 is working perfectly directly from the JP-3163B board to the VFD. No PWM to analog board required.
    It took some time to sort out the settings, but it works.
    of course you need to set the VFD to "listen" to external input. In my (A2-2015B) this is Pn03 to 4 (external 0-10v signal) and Pn04 to 2 (External signal control)

    If someone else has to solution to do the same with USB-CNC from PlanetCNC (version: 2.10.1208.601 which cannot be upgraded because the JP-3163B is not from PlanetCNC)



    Attached Thumbnails Attached Thumbnails CNC 6040 connection FI  MK100-2S1.5G-DK to mainboard JP-3163B cabling question-motor-outputs-large-jpg   CNC 6040 connection FI  MK100-2S1.5G-DK to mainboard JP-3163B cabling question-output-signals-large-jpg   CNC 6040 connection FI  MK100-2S1.5G-DK to mainboard JP-3163B cabling question-spindle-setup-large-jpg   CNC 6040 connection FI  MK100-2S1.5G-DK to mainboard JP-3163B cabling question-jp-3163b-board-connections-large-jpg  

    CNC 6040 connection FI  MK100-2S1.5G-DK to mainboard JP-3163B cabling question-vfd-connections-large-jpg  
    Last edited by lastdown; 12-31-2020 at 10:45 AM.


  8. #28

    Default Re: CNC 6040 connection FI MK100-2S1.5G-DK to mainboard JP-3163B cabling question

    Sorry new link here (can't edit the posting anymore):
    You are looking at Mach3 Version 3.043


    Last edited by lastdown; 12-31-2020 at 12:11 PM.


Page 2 of 2 FirstFirst 12

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

CNC 6040 connection FI  MK100-2S1.5G-DK to mainboard JP-3163B cabling question

CNC 6040 connection FI  MK100-2S1.5G-DK to mainboard JP-3163B cabling question

CNC 6040 connection FI  MK100-2S1.5G-DK to mainboard JP-3163B cabling question