Charter Oak Automation Support Forum - Page 33


Page 33 of 34 FirstFirst ... 233031323334 LastLast
Threads 641 to 660 of 667

Forum: Charter Oak Automation Support Forum

Discuss Industrial Hobbies/Charter Oak Automation Milling machines and get direct support here.

    • Replies: 7
    • Views: 3,244
    04-07-2006, 04:19 PM Go to last post
  1. Any helpful hints for tramming?

    Started by BEDFORD‎, 03-31-2006 11:38 AM
    attributed, cabine, down, noticed, square, then, tramming, travel
    • Replies: 3
    • Views: 1,712
    04-03-2006, 02:36 PM Go to last post
  2. v3 retrofit kit

    Started by xovationx‎, 03-23-2006 04:04 PM
    added/changed, kit, kits, sold, talked
    • Replies: 0
    • Views: 1,329
    03-23-2006, 04:04 PM Go to last post
  3. ballscrew sizes on the IH mill?

    Started by xovationx‎, 03-22-2006 06:51 PM
    ballscrew, ballscrews, ground, long, mill, wan
    • Replies: 0
    • Views: 1,423
    03-22-2006, 06:51 PM Go to last post
  4. Optical Limits

    Started by JOE65‎, 03-19-2006 12:08 PM
    axis, high, limits, optical, voltage
    • Replies: 1
    • Views: 1,404
    03-21-2006, 11:06 PM Go to last post
  5. IH mill stand

    Started by Runner4404spd‎, 03-15-2006 09:06 AM
    concrete, crete, fabrication, mill, mill stand, save, stand
    • Replies: 2
    • Views: 1,971
    03-20-2006, 03:51 PM Go to last post
  6. What gear oil are you using?

    Started by KEYTEEM‎, 02-18-2006 07:41 AM
    ,part, good, machine, minutes, running, window
    • Replies: 9
    • Views: 7,149
    02-24-2006, 12:16 PM Go to last post
  7. Cool Quill micro feed?

    Started by KEYTEEM‎, 02-05-2006 07:56 PM
    cor, end, feed, micro, mos, next, quill
    • Replies: 5
    • Views: 1,637
    02-18-2006, 07:00 AM Go to last post
  8. 4th axis

    Started by Zumba‎, 01-30-2006 11:12 PM
    4th, appears, axis, cnc, its, ques, stepper
    • Replies: 1
    • Views: 1,550
    02-02-2006, 03:10 AM Go to last post
  9. Retro fitting

    Started by new2this‎, 01-21-2006 12:11 PM
    cnc, fitting, idea, maybe, not, retro, thing, wan
    • Replies: 1
    • Views: 1,842
    01-21-2006, 07:21 PM Go to last post
  10. Question ballscrew for IH mill

    Started by KEYTEEM‎, 12-18-2005 09:14 PM
    1200, bearing, belt, confused, everyone, mill, onto, since, wan
    • Replies: 4
    • Views: 2,942
    01-18-2006, 12:24 PM Go to last post
  11. Industrial Hobbies Forum

    Started by MikeAber‎, 07-12-2005 04:47 PM
    2 Pages
    1 2
    • Replies: 29
    • Views: 17,628
    01-06-2006, 10:56 PM Go to last post
  12. Question gear train/motor

    Started by KEYTEEM‎, 12-18-2005 09:40 PM
    assume, away, case, doi, gear, motor, needed, wan
    • Replies: 2
    • Views: 1,938
    12-21-2005, 11:53 AM Go to last post
  13. Motor Problems

    Started by MikeAber‎, 11-18-2005 06:18 PM
    arcing, mike, motor, problems, turned
    • Replies: 7
    • Views: 2,078
    12-13-2005, 12:22 PM Go to last post
  14. Spindle Bearing/Tool Carousel Motor???

    Started by AdvancedMfg‎, 12-04-2005 10:25 PM
    down, find, kia, knows, machine, next, number, spindle
    • Replies: 0
    • Views: 2,256
    12-04-2005, 10:25 PM Go to last post
  15. IH mill motor upgrade

    Started by Randall‎, 08-09-2005 12:02 PM
    motor, randy, reccomends, results, upgrade
    • Replies: 13
    • Views: 4,065
    11-14-2005, 03:04 PM Go to last post
  16. Problem With IH Limit Switch.

    Started by Willyb‎, 10-30-2005 02:21 PM
    cnc, discrepancy, its, limit, next, output, volts, wire
    • Replies: 5
    • Views: 2,125
    11-06-2005, 06:17 PM Go to last post
  17. Moved: newbie help bit selection

    Started by DrStein99‎, 09-01-2006 12:22 AM
    bit, newbie, selection
    •  
    •  
  18. Moved: Auto changers and Cones.

    Started by baldusi‎, 09-01-2006 12:22 AM
    auto, changers, cones
    •  
    •  
  19. DIY CNC conversion

    Started by broken003‎, 10-16-2005 03:49 PM
    asking, bring, cnc, conversion, diy, drop
    • Replies: 0
    • Views: 1,987
    10-16-2005, 03:49 PM Go to last post

Page 33 of 34 FirstFirst ... 233031323334 LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 5 users browsing this forum. (0 members & 5 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands