Charter Oak Automation Support Forum


Page 1 of 34 123411 ... LastLast
Threads 1 to 20 of 665

Forum: Charter Oak Automation Support Forum

Discuss Industrial Hobbies/Charter Oak Automation Milling machines and get direct support here.

  1. IH Controller schmaticm + specs

    Started by qbit‎, 04-14-2021 09:36 PM
    charter, cnc, control electronics, industrial hobbies mill, specs
    • Replies: 1
    • Views: 353
    05-14-2021, 09:46 AM Go to last post
  2. ball screw nut replacement

    Started by bit pusher‎, 04-12-2021 11:11 PM
    ball, nut, replacement, screw, tommy
    • Replies: 4
    • Views: 487
    04-23-2021, 10:48 AM Go to last post
    • Replies: 0
    • Views: 263
    04-16-2021, 11:32 PM Go to last post
  3. Moved: Schematic for Industrial Hobbies CNC mill controller

    Started by qbit‎, 04-12-2021 10:00 PM
    •  
    •  
  4. IH ENCODERS

    Started by bohica‎, 12-30-2020 07:03 PM
    apparently, bit, cnc, dust, encoder
    • Replies: 0
    • Views: 668
    12-30-2020, 07:03 PM Go to last post
  5. IH SERVO MOTOR

    Started by bohica‎, 12-10-2020 12:21 PM
    jim, motor, replacement, sell, servo
    • Replies: 1
    • Views: 762
    12-10-2020, 02:54 PM Go to last post
  6. Sometimes the Z axis Drops after power-down

    Started by pryotex‎, 03-25-2017 04:28 AM
    drops, occurred, power, time, tool
    • Replies: 8
    • Views: 5,253
    01-22-2020, 04:30 PM Go to last post
  7. Large seal in head under the motor, 35x62x...?

    Started by QSIMDO‎, 12-26-2019 04:45 PM
    35x62x12, head, motor, removed, seal
    • Replies: 0
    • Views: 1,015
    12-26-2019, 04:45 PM Go to last post
  8. Head bolt dimensions head spacer

    Started by williamsmotower‎, 12-05-2019 11:53 AM
    bolt, column, dimensions, head, special
    • Replies: 0
    • Views: 1,057
    12-05-2019, 11:53 AM Go to last post
  9. Glad I didnt Buy One !

    Started by madman‎, 09-15-2014 10:50 AM
    • Replies: 7
    • Views: 4,659
    10-02-2019, 09:51 PM Go to last post
  10. How to Change Bearings - COA Square Col

    Started by Danal‎, 09-20-2019 05:58 PM
    bearings, load, running, spindle, square
    • Replies: 5
    • Views: 1,426
    09-22-2019, 06:08 PM Go to last post
  11. Need Help!- Post processor for Osai control system from Mastercam x4

    Started by buterbrodas‎, 01-28-2015 05:06 AM
    axis, mastercam, posts, system, tbi, working
    • Replies: 2
    • Views: 2,812
    08-11-2019, 05:25 AM Go to last post
  12. Charter Oak not responding?

    Started by QSIMDO‎, 08-01-2019 11:22 AM
    anymore, full, mail, mailbox, voice
    • Replies: 2
    • Views: 1,454
    08-02-2019, 03:56 PM Go to last post
  13. Angry ARGH! backlash killing parts! Anyone have some info?

    Started by Farasien‎, 10-05-2018 11:35 PM
    ball, nuts, put, reason, screws
    • Replies: 11
    • Views: 2,389
    07-09-2019, 11:05 PM Go to last post
  14. BT/NT30 Spindle for 12Z Mill?

    Started by tulsah‎, 01-17-2019 10:04 PM
    12z, assuming, bt/nt30, cnc, spindle
    • Replies: 13
    • Views: 3,847
    05-16-2019, 09:27 AM Go to last post
  15. Model C8250

    Started by crazybrit‎, 04-22-2019 09:04 PM
    • Replies: 2
    • Views: 1,059
    04-23-2019, 08:18 PM Go to last post
  16. Spindle Problem?

    Started by bohica‎, 03-07-2019 02:46 PM
    cnc, problem, rpm, running, spindle
    • Replies: 5
    • Views: 1,234
    04-07-2019, 12:44 PM Go to last post
  17. Problem- Adaptacion conector para un encoder A860-0309-T302 a conector Fanuc

    Started by xasart‎, 03-10-2019 08:02 AM
    circular, cnc, conector, los, para
    • Replies: 0
    • Views: 862
    03-10-2019, 08:02 AM Go to last post
  18. Need Help!- Getting 4th axis set up

    Started by djohnson81‎, 01-28-2019 11:11 AM
    4th, axis, tapatalk, sm-g965u1, plugged
    • Replies: 1
    • Views: 852
    01-28-2019, 04:34 PM Go to last post

Page 1 of 34 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 1 users browsing this forum. (0 members & 1 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands