Build Thread loady builds a cnc machine - Page 2


Page 2 of 2 FirstFirst 12
Results 21 to 28 of 28

Thread: loady builds a cnc machine

  1. #21
    Registered
    Join Date
    May 2006
    Location
    Canada
    Posts
    58
    Downloads
    0
    Uploads
    0

    Default

    thanks gentlemen. i ran it for another 10 hours today and temperatures seemed to level off about 140. cuts were a little lighter today. i would like to see it a little cooler, but as you mentioned cruiser it is still breaking in. i have a thermocouple on it and am monitoring closely.

    to my knowledge you're correct bob. 160 degrees is the warmest i would ever run a bearing. as for where and which textbooks say that i can't remember. it's been a long time since i finished my mechanical engineering degree ;-)

    dad used to say... "once is ignorance. the second time you're stupid!"


  2. #22
    Member
    Join Date
    Aug 2004
    Location
    US
    Posts
    2849
    Downloads
    0
    Uploads
    0

    Default

    Loadedagain,

    Using the hockey puck isolators, how do you level the mill?

    Can you keep the mill from walking across the enclosure?

    I'm getting ready to build an enclosure for my CNCed X3 and was planning on having a flat bottom on the bottom side where it sits on a workbench and countour (slope) the inside base with plywood and then fiberglass the inside maybe two layers of 6 ounce fabric.

    Thanks,

    Paul



  3. #23
    Registered
    Join Date
    May 2006
    Location
    Canada
    Posts
    58
    Downloads
    0
    Uploads
    0

    Default

    i'm not following you... it's bolted down so it doesn't walk anywhere!

    dad used to say... "once is ignorance. the second time you're stupid!"


  4. #24
    Member
    Join Date
    Feb 2009
    Location
    USA
    Posts
    187
    Downloads
    0
    Uploads
    0

    Default

    Extremely well done control cabinet. You should be VERY proud of your work!!!!

    RWW



  5. #25
    Registered
    Join Date
    May 2006
    Location
    Canada
    Posts
    58
    Downloads
    0
    Uploads
    0

    Default

    thanks for the compliment mate. was a bit of effort to get it the way it is, but i'm quite pleased with the result.

    now for hockey pucks! a picture is worth a thousand words! i used a hole saw on the plywood base... 2" i think. the pucks are 3/4" so they sit 1/4" proud from the base. i then drilled 3/4" holes in them for the studs and mounted the mill to the steel base like you would normally.

    oh yeah. to seal everything i squirted a bunch of silicone around, then fiberglassed the pucks into the base



    dad used to say... "once is ignorance. the second time you're stupid!"


  6. #26
    Registered
    Join Date
    May 2006
    Location
    Canada
    Posts
    58
    Downloads
    0
    Uploads
    0

    Default

    while i'm at it here's a pic today of the setup. my *huge* 8" vise seems to fit ok and everything else is holding up well so far. haven't had any difficulties with the machine at all once the motors were tuned properly. i have about 0.004" backlash in one ballscrew, but i'll take it our and reset the preload when i get a chance. i can't say enough about the mill. if you're prepped well and do the cnc conversion correctly it's a very cost effective and reliable machine.



    and here is a shot of the parts i ran through yesterday. still a couple ops to do today, then off to the annodizer.



    dad used to say... "once is ignorance. the second time you're stupid!"


  7. #27
    Registered
    Join Date
    Feb 2011
    Location
    united states
    Posts
    212
    Downloads
    0
    Uploads
    0

    Default Re: loady builds a cnc machine

    Very nice enclosure and set up



  8. #28
    Member
    Join Date
    Sep 2017
    Location
    United States
    Posts
    143
    Downloads
    0
    Uploads
    0

    Default

    I've been looking for enclosure ideas. This is a very nice enclosure however my personal concerns are if I ever want to do something manually or need to access the machine for repairs. My largest bench mill is 1300lbs and has pedastels locking it in place on the base chip stand so sliding it around is never happening if I need to access anything. I'm thinking I may have to go with something using an extruded frame and removable panels. I've seen some with tub surround material however I wonder if that wouldn't vibrate quite a bit as you mention with sheet metal. I need to build 3 enclosures for 3 machines so the task is ahead of me. There is a company making them for $1,000 each. I'd like to make all 3 for that budget but I am doubting it is even possible to buy the materials I would want to use for them. Perhaps for my schedule I may just have them build me glass cabinets. Very nice CNC cabinet it looks top notch. How has it held up over the past few years to coolant and that water hose you use to clean it up?



    Quote Originally Posted by Loadedagain View Post
    hi all.

    i've been about here for a while, but don't post too often so i had better re-introduce myself. my name is colin. mechanical engineer during the day, car racer/make stuff/get into trouble the rest of the time.

    i bought an industrial hobbies mill and cnc conversion from aaron a few years back. since i have a bridgeport also i took my time putting it together... how long ago did he sell the biz?... that's time taking. recently i decided i had better finish it, or sell it.... so finish it i will.

    here's the setup stuffed into the corner of my shop



    i built the enclosure out of wood and laminated it with fiberglass and white gel coat. was going to do a sheetmetal enclosure, but hear tales of big noise and vibration. the doors are not hung yet, but they are wood also with plexi windows so i can see my machine crash.

    the control box off to the left is below:


    the control panel has 2 campbel breakout boards and relay panel as well as the gekos and a little plc i'm using to control all the odds and ends.

    it's a work in progress so i apologize for the messy wiring. i'll get it all sorted out pdq. if you see anything that seems fishy please point it out. i'm doing my best to not blow things up, but i'm pretty sure some magic smoke will get out.




Page 2 of 2 FirstFirst 12

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

loady builds a cnc machine

loady builds a cnc machine