Centroid CNC Control Products


Page 1 of 17 123411 ... LastLast
Threads 1 to 20 of 340

Forum: Centroid CNC Control Products

Discuss Centroid CNC Control Products, systems and project here!

  1. Repeated 411 motion error on y and z axis m400

    Started by alh2411‎, Yesterday 08:48 PM
    axis, error, home, manually, run
    • Replies: 1
    • Views: 86
    Yesterday, 10:13 PM Go to last post
  2. 4th axis label when homing

    Started by forhire‎, 12-05-2019 03:57 PM
    • Replies: 1
    • Views: 274
    12-05-2019, 08:37 PM Go to last post
  3. Centroid Acorn experiences?

    Started by steve_p‎, 06-06-2019 12:44 PM
    4 Pages
    1 2 3 4
    • Replies: 37
    • Views: 2,267
    11-15-2019, 09:03 PM Go to last post
  4. Anyone use Centroid control on a VMC?

    Started by Sam_Beckham‎, 11-13-2019 06:30 PM
    • Replies: 4
    • Views: 253
    11-15-2019, 03:05 PM Go to last post
  5. Centroid M400 code numbers

    Started by h_2_o‎, 03-01-2005 12:06 AM
    2 Pages
    1 2
    • Replies: 23
    • Views: 14,259
    11-06-2019, 09:33 AM Go to last post
  6. PWM Pulse Width Modular for Laser

    Started by artracing‎, 10-18-2019 11:02 PM
    laser, output, pwm, rob, running
    • Replies: 4
    • Views: 252
    10-26-2019, 02:05 AM Go to last post
  7. Acorn expansion

    Started by jacep‎, 10-26-2019 01:22 AM
    acorn, boards, expansion, input, software
    • Replies: 1
    • Views: 221
    10-26-2019, 01:52 AM Go to last post
  8. Motion error 411 axis full power without motion

    Started by roreyes‎, 09-27-2019 04:19 PM
    • Replies: 1
    • Views: 153
    09-28-2019, 04:05 PM Go to last post
  9. CNC10 (Linux) Z axis dropping over run time

    Started by SEK22Hornet‎, 09-18-2019 03:13 PM
    axis, dropped, encoder, part, ran
    • Replies: 6
    • Views: 320
    09-22-2019, 07:09 PM Go to last post
  10. CNC10 (Linux) Soft limits?

    Started by SEK22Hornet‎, 09-18-2019 03:04 PM
    cnc, limits, set, soft, switches
    • Replies: 2
    • Views: 183
    09-19-2019, 12:57 AM Go to last post
  11. Newbie- Home/Limit Switch Guidance

    Started by Joey2point0‎, 09-17-2019 07:57 AM
    • Replies: 2
    • Views: 199
    09-17-2019, 10:41 AM Go to last post
  12. x axis not moving - blown fuse shorted FET

    Started by SEK22Hornet‎, 09-09-2019 12:48 AM
    axis, chip, cnc, fet, shorted
    • Replies: 1
    • Views: 187
    09-16-2019, 08:24 AM Go to last post
  13. need to remove inoperative 4th axis dc drive board

    Started by SEK22Hornet‎, 09-11-2019 06:15 PM
    4th, axis, board, remove, software
    • Replies: 2
    • Views: 205
    09-16-2019, 08:21 AM Go to last post
  14. Newbie- Cheetah II DC Drive And AcornCNC controller

    Started by Joey2point0‎, 09-12-2019 01:29 PM
    • Replies: 6
    • Views: 284
    09-13-2019, 09:09 AM Go to last post
  15. Hurco SM1 Control Replacement

    Started by Phil_arch‎, 07-22-2019 05:31 PM
    cnc, controller, hurco, machine, servo
    • Replies: 2
    • Views: 390
    08-29-2019, 02:14 PM Go to last post
  16. Digitizing and usability

    Started by Dave Koehler‎, 03-29-2018 09:06 PM
    cad, dig, file, program, tips
    • Replies: 11
    • Views: 1,569
    08-28-2019, 04:36 PM Go to last post
  17. Newbie- Acorn/Beagle Board Green. GROVE I2C output for i/o expansion

    Started by FritziAnn‎, 08-11-2019 10:47 PM
    expansion, factory, software/hardware, thoughts, variables
    • Replies: 7
    • Views: 488
    08-13-2019, 01:21 PM Go to last post
  18. Newbie- CNC12 New Parameters

    Started by FritziAnn‎, 08-11-2019 11:54 PM
    document, mini, parameters, plc, referenced
    • Replies: 2
    • Views: 273
    08-12-2019, 12:05 PM Go to last post
  19. Centriod will not home

    Started by bobterisch‎, 08-12-2019 10:27 AM
    • Replies: 1
    • Views: 148
    08-12-2019, 11:57 AM Go to last post
  20. Global Variables for Custom M Codes

    Started by ineffable77‎, 08-02-2019 04:05 PM
    custom, macro, parameters, read, variables
    • Replies: 1
    • Views: 252
    08-04-2019, 04:03 AM Go to last post

Page 1 of 17 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 6 users browsing this forum. (0 members & 6 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands