New Here HAAS SUPER MINI MILL 2004 - SINGLE PHASE HELP


Page 1 of 2 12 LastLast
Results 1 to 12 of 24

Thread: HAAS SUPER MINI MILL 2004 - SINGLE PHASE HELP

  1. #1
    Registered
    Join Date
    Feb 2018
    Location
    Canada
    Posts
    25
    Downloads
    0
    Uploads
    0

    Default HAAS SUPER MINI MILL 2004 - SINGLE PHASE HELP

    Hey Guys,

    Newbie here...Needed some help with hooking up a 2004 SMM on Single Phase Power.

    I have been trying to find relevant info for my machine but there is always some sort of variance.

    I know i am close just missing something very simple.

    Any help and/or pics would help. Note I have a Large Input Transformer at the bottom with 4 Voltage Range Inputs.

    Thanks in advance!!

    CCF

    Similar Threads:


  2. #2
    Registered
    Join Date
    May 2008
    Location
    Canada
    Posts
    596
    Downloads
    0
    Uploads
    0

    Default Re: HAAS SUPER MINI MILL 2004 - SINGLE PHASE HELP

    Do you have this document, look on page 9

    Jeff

    Attached Thumbnails Attached Thumbnails HAAS SUPER MINI MILL 2004 - SINGLE PHASE HELP-es0205l-minimill-pdf  


  3. #3
    Registered
    Join Date
    Feb 2018
    Location
    Canada
    Posts
    25
    Downloads
    0
    Uploads
    0

    Default Re: HAAS SUPER MINI MILL 2004 - SINGLE PHASE HELP

    Hey Jeff,

    I was reading that and one part confuses me.

    Page 5, Top of page #3. The Two Different Input Connections for Wire # 74.

    I dont have a Small Input Transformer but a Big one at teh bottom with 4 different Ranges to connect to.

    my input is 250 for connected to 244-260V with wires #74, 75, & 76


    NOTE: The Red Wire in L2 is Not Live. That is my Neutral Wire but not hooked up to anything.



    Attached Thumbnails Attached Thumbnails HAAS SUPER MINI MILL 2004 - SINGLE PHASE HELP-img_7740-jpg   HAAS SUPER MINI MILL 2004 - SINGLE PHASE HELP-img_7741-jpg   HAAS SUPER MINI MILL 2004 - SINGLE PHASE HELP-img_7742-jpg  


  4. #4
    Registered
    Join Date
    Feb 2018
    Location
    Canada
    Posts
    25
    Downloads
    0
    Uploads
    0

    Default Re: HAAS SUPER MINI MILL 2004 - SINGLE PHASE HELP

    Quote Originally Posted by jeffrey001 View Post
    Do you have this document, look on page 9

    Jeff
    Also i was just reading somewhere and am more confused now!

    "Personally, I would try and find a standard mini mill rather than the super mini mill. They are usually a little cheaper, more bullet proof, and can run on single phase."

    Does this mean a Super Mini Mill CAN NOT run on Single Phase?

    Thanks



  5. #5
    Registered
    Join Date
    May 2008
    Location
    Canada
    Posts
    596
    Downloads
    0
    Uploads
    0

    Default Re: HAAS SUPER MINI MILL 2004 - SINGLE PHASE HELP

    I don't understand, the red wire is not hot, it should be. Black and red should be hot and white should be neutral.

    Jeff



  6. #6
    Registered
    Join Date
    Feb 2018
    Location
    Canada
    Posts
    25
    Downloads
    0
    Uploads
    0

    Default Re: HAAS SUPER MINI MILL 2004 - SINGLE PHASE HELP

    Quote Originally Posted by jeffrey001 View Post
    I don't understand, the red wire is not hot, it should be. Black and red should be hot and white should be neutral.

    Jeff
    it was just a wiring thing.. i can just swap the wires so Red is Hot and White is Neutral (swap else where just ignore colors). What i'm saying is that the Center Connection L2 has nothing connected to it.



  7. #7
    Registered
    Join Date
    Feb 2018
    Location
    Canada
    Posts
    25
    Downloads
    0
    Uploads
    0

    Default

    Ok I changed the wiring to reflect correct colours.

    Attached Thumbnails Attached Thumbnails HAAS SUPER MINI MILL 2004 - SINGLE PHASE HELP-img_7743-jpg  


  8. #8
    Gold Member
    Join Date
    Jan 2005
    Location
    USA
    Posts
    7836
    Downloads
    0
    Uploads
    0

    Default Re: HAAS SUPER MINI MILL 2004 - SINGLE PHASE HELP

    Quote Originally Posted by CCF_CUSTOMS View Post
    Ok I changed the wiring to reflect correct colours.
    What size spindle do you have that will tell you if you can run on single phase or not

    I hope you have not connected the Neutral you should not have that at all in you cable Just 2 Hot and Ground

    The first Photo is incorrect Red and Black or Black and Black are connected to the 2 outside switch Terminals only, the center Terminal is not connected for single Phase

    Mactec54


  9. #9
    Registered
    Join Date
    May 2008
    Location
    Canada
    Posts
    596
    Downloads
    0
    Uploads
    0

    Default Re: HAAS SUPER MINI MILL 2004 - SINGLE PHASE HELP

    If your mill is supposed to run on single phase, you should not connect the white wire, Normally, 3 inputs are for 3 phases, 1 phase per wire, if you hook it up on single phase, only the red and black should be use, on L1 and L3.

    Use this info at your own risk, I'm not an electrician.

    Jeff



  10. #10
    Registered
    Join Date
    Feb 2018
    Location
    Canada
    Posts
    25
    Downloads
    0
    Uploads
    0

    Default Re: HAAS SUPER MINI MILL 2004 - SINGLE PHASE HELP

    Quote Originally Posted by mactec54 View Post
    What size spindle do you have that will tell you if you can run on single phase or not

    I hope you have not connected the Neutral you should not have that at all in you cable Just 2 Hot and Ground

    The first Photo is incorrect Red and Black or Black and Black are connected to the 2 outside switch Terminals only, the center Terminal is not connected for single Phase

    Its was wired correctly, The Colors were just swapped. at all time the hot was only on outside and center was a dead line.


    The Supply to the machine comes from a Single Phase supply The Neutral is not going to anything. it is a deadline.

    Only outsides Hot, 125V & 125V.

    Spindle is 15k rpm, 15HP. it is the Upgraded Option.

    Attached Thumbnails Attached Thumbnails HAAS SUPER MINI MILL 2004 - SINGLE PHASE HELP-smm-jpg  


  11. #11
    Registered
    Join Date
    Feb 2018
    Location
    Canada
    Posts
    25
    Downloads
    0
    Uploads
    0

    Default Re: HAAS SUPER MINI MILL 2004 - SINGLE PHASE HELP

    Quote Originally Posted by jeffrey001 View Post
    If your mill is supposed to run on single phase, you should not connect the white wire, Normally, 3 inputs are for 3 phases, 1 phase per wire, if you hook it up on single phase, only the red and black should be use, on L1 and L3.

    Use this info at your own risk, I'm not an electrician.

    Jeff
    The Center is not connected to anything at the other end.



  12. #12
    Registered
    Join Date
    May 2008
    Location
    Canada
    Posts
    596
    Downloads
    0
    Uploads
    0

    Default Re: HAAS SUPER MINI MILL 2004 - SINGLE PHASE HELP

    If your spindle is 15HP, then it surely 3 phases, you'll need a phase converter to get 3 phases

    https://www.americanrotary.com/



    Jeff



Page 1 of 2 12 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

HAAS SUPER MINI MILL 2004 - SINGLE PHASE HELP

HAAS SUPER MINI MILL 2004 - SINGLE PHASE HELP