Bridgeport / Hardinge Mills


Page 1 of 263 12341151101 ... LastLast
Threads 1 to 20 of 5255

Forum: Bridgeport / Hardinge Mills

Discuss Bridgeport and Hardinge mills here!

  1. New Machine Build- Bridgeport quill ball screw conversion

    Started by Se5a‎, Yesterday 02:27 PM
    ball, quill, screw, encoder, drive
    • Replies: 0
    • Views: 54
    Yesterday, 02:27 PM Go to last post
  2. Problem- Acra Mill to CNC, XY yoke

    Started by keith20mm‎, 12-04-2013 10:54 AM
    four
    • Replies: 2
    • Views: 723
    04-05-2020, 11:08 PM Go to last post
  3. Bidgeport EZTRAK Back Up

    Started by KK80‎, 04-05-2020 07:12 AM
    • Replies: 0
    • Views: 61
    04-05-2020, 07:12 AM Go to last post
  4. Advise needed Transformers / Caps etc

    Started by mongoose‎, 04-04-2020 11:36 PM
    • Replies: 0
    • Views: 78
    04-04-2020, 11:36 PM Go to last post
  5. New Machine Build- 90vdc supply

    Started by Se5a‎, 04-03-2020 09:09 PM
    supply, motor, power, building, conversion
    • Replies: 2
    • Views: 116
    04-04-2020, 09:24 AM Go to last post
  6. Bridgeport TorqCut 22 Rebuild

    Started by AshG‎, 03-17-2020 05:47 PM
    • Replies: 16
    • Views: 481
    04-03-2020, 10:26 AM Go to last post
    • Replies: 0
    • Views: 68
    04-02-2020, 02:06 PM Go to last post
  7. Boss 8 CNC retrofit and 5 HP upgrade - Build thread

    Started by dbsharp‎, 01-19-2020 03:08 PM
    2 Pages
    1 2
    • Replies: 36
    • Views: 1,429
    03-30-2020, 06:30 PM Go to last post
  8. Need Help!- Bridgeport Interact Series 1 - TNC145 Tapping Cycle Issues

    Started by benjdoe‎, 03-25-2020 11:27 AM
    bridgeport, cnc, forum, spindle, thread
    • Replies: 12
    • Views: 215
    03-27-2020, 10:06 AM Go to last post
    • Replies: 8
    • Views: 1,890
    03-24-2020, 12:29 AM Go to last post
  9. Need Help!- BRIDGEPORT VMC- BOSCH DRIVES-SEM MOTORS

    Started by sputnikprec‎, 03-17-2020 08:00 AM
    bosch, found, machine, motor, motors
    • Replies: 2
    • Views: 140
    03-23-2020, 05:54 PM Go to last post
  10. Need Help!- TorqCut 22 Transmission

    Started by AshG‎, 03-17-2020 05:41 PM
    ash, manuals, missing, service, transmission
    • Replies: 3
    • Views: 154
    03-23-2020, 12:42 PM Go to last post
  11. Need Help!- AH HA Software, Bridgeport CNC

    Started by jim2000‎, 03-21-2020 02:46 AM
    • Replies: 2
    • Views: 215
    03-22-2020, 12:13 PM Go to last post
  12. Post Bridgeport Series 1 CNC

    Started by jim2000‎, 03-15-2020 10:10 PM
    board, bridgeport series ! cnc, cnc, steppers, upgrade
    • Replies: 3
    • Views: 354
    03-20-2020, 12:52 PM Go to last post
    • Replies: 9
    • Views: 474
    03-19-2020, 06:52 PM Go to last post
  13. Newbie- Bridgeport EZ Trak DX Series 1

    Started by NKY003‎, 01-31-2020 03:44 AM
    • Replies: 1
    • Views: 259
    03-18-2020, 12:48 PM Go to last post
  14. EZ-TRAK SX Problem/Software

    Started by Valentinik‎, 03-26-2016 05:44 PM
    battery, ez-trak, machine, motherboard, software
    • Replies: 7
    • Views: 1,139
    03-18-2020, 12:45 PM Go to last post
  15. Bridge port pulley and timing system modification

    Started by feconkar‎, 03-18-2020 01:02 AM
    machinist, rpm, speed, step, working
    • Replies: 2
    • Views: 145
    03-18-2020, 12:30 PM Go to last post
    • Replies: 0
    • Views: 72
    03-17-2020, 11:40 AM Go to last post
  16. Exclamation Z measuring device defective

    Started by wildblood7‎, 11-02-2018 08:21 AM
    cable, disappears, drive, machine, posts
    • Replies: 2
    • Views: 641
    03-12-2020, 09:40 AM Go to last post

Page 1 of 263 12341151101 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 38 users browsing this forum. (2 members & 36 guests)

  1. Jonp,
  2. Lessons

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands