Torq Cut 22 - Spindle oscillates in M19 Spindle Orient mode


Results 1 to 7 of 7

Thread: Torq Cut 22 - Spindle oscillates in M19 Spindle Orient mode

  1. #1
    Member
    Join Date
    Apr 2009
    Location
    USA
    Posts
    14
    Downloads
    0
    Uploads
    0

    Default Torq Cut 22 - Spindle oscillates in M19 Spindle Orient mode

    Hello,

    I have an issue on a new to us 1995 Bridgeport Tor Cut 22 where the spindle oscillates when doing a spindle orient and tool change operation, which can cause some issues with changing tools ( so far only a load pop noise when picking up a new tool)
    If I do an M19 command the spindle locks up and oscillates probably a couple degrees. If a grab the spindle the oscillation will stop. I have added a video of what is happening.

    Looking for some input to see if there are settings I need to change to fix this, or if this is normal for this machine.



    Similar Threads:


  2. #2
    Member
    Join Date
    Aug 2008
    Location
    USA
    Posts
    7
    Downloads
    0
    Uploads
    0

    Default Re: Torq Cut 22 - Spindle oscillates in M19 Spindle Orient mode

    Look at the belt that goes from the spindle to the encoder. If it is loose it can cause this problem as it is hunting back and forth to hold the position.



  3. #3
    Member
    Join Date
    Apr 2009
    Location
    USA
    Posts
    14
    Downloads
    0
    Uploads
    0

    Default Re: Torq Cut 22 - Spindle oscillates in M19 Spindle Orient mode

    Thank you,
    I gave that a check and tightened it up but it did not resolve the issue.
    I was looking at other threads and think it could be the spindle gain, does that sound like the next step? The actual spindle speed is always a couple RPM less than requested and more as the spindle speed increases if that gives any other hints to the issue.



  4. #4
    Member
    Join Date
    Apr 2009
    Location
    USA
    Posts
    14
    Downloads
    0
    Uploads
    0

    Default Re: Torq Cut 22 - Spindle oscillates in M19 Spindle Orient mode

    I think that i have narrowed the problem down to the transmission, I can feel play when manually turning the spindle back and forth that seems about the distance of the oscillation. then checked all the pulleys and they are all tight. I have all the manuals but there isnt anything in there on servicing the transmission. Is there a place to get this information? Thanks



  5. #5
    Member
    Join Date
    Mar 2016
    Location
    United States
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default Re: Torq Cut 22 - Spindle oscillates in M19 Spindle Orient mode

    Adjusting parameter #69 worked for me.



  6. #6
    Member
    Join Date
    Mar 2016
    Location
    United States
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default Re: Torq Cut 22 - Spindle oscillates in M19 Spindle Orient mode

    Adjusting parameter #69 fixed the oscillating issue but has caused an error with rigid tapping breaking taps.
    Any advice on what to try next?




  7. #7
    Member
    Join Date
    Mar 2016
    Location
    United States
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default Re: Torq Cut 22 - Spindle oscillates in M19 Spindle Orient mode

    Solved.
    After Adjusting parameter #69 to fix the oscillating issue, adjust parameter #64 to correct the rigid tapping issue.





Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Torq Cut 22 - Spindle oscillates in M19 Spindle Orient mode

Torq Cut 22 - Spindle oscillates in M19 Spindle Orient mode