TC Series Yaskawa Motors on Z


Results 1 to 7 of 7

Thread: TC Series Yaskawa Motors on Z

  1. #1
    Member
    Join Date
    Dec 2009
    Location
    USA
    Posts
    482
    Downloads
    0
    Uploads
    0

    Default TC Series Yaskawa Motors on Z

    Does anyone know the model number of the Yaskawa motor on the Z axis of the Torq Cut machines? I am trying to find out what KW rating it is.
    Was it belted to the Z axis ballscrew at 1:1?

    Are the X/Y Axis Yaskawa motors the same or different than Z?

    Did any of the TC Series machines have a counter balance weight on the Z axis? I know the TC22-30 did not. This would make a difference in the size of the Yaskawa motor on Z

    Thanks in advance!
    Marty

    Similar Threads:


  2. #2
    Member
    Join Date
    Jan 2005
    Location
    USA
    Posts
    10313
    Downloads
    0
    Uploads
    0

    Default Re: TC Series Yaskawa Motors on Z

    Quote Originally Posted by Marty_Escarcega View Post
    Does anyone know the model number of the Yaskawa motor on the Z axis of the Torq Cut machines? I am trying to find out what KW rating it is.
    Was it belted to the Z axis ballscrew at 1:1?

    Are the X/Y Axis Yaskawa motors the same or different than Z?

    Did any of the TC Series machines have a counter balance weight on the Z axis? I know the TC22-30 did not. This would make a difference in the size of the Yaskawa motor on Z

    Thanks in advance!
    Marty
    The Yaskawa servo motors are 1300w for X Y and Z the drives are 1500w Z axes Ballscrews 5mm pitch 1:1 Ratio no counter weight on the small machines, on the larger machines they have a 30 tooth on the motor and a 36 tooth on the Ballscrew

    SGMG-13A2AB

    Mactec54


  3. #3
    Member
    Join Date
    Dec 2009
    Location
    USA
    Posts
    482
    Downloads
    0
    Uploads
    0

    Default Re: TC Series Yaskawa Motors on Z

    Quote Originally Posted by mactec54 View Post
    The Yaskawa servo motors are 1300w for X Y and Z the drives are 1500w Z axes Ballscrews 5mm pitch 1:1 Ratio no counter weight on the small machines, on the larger machines they have a 30 tooth on the motor and a 36 tooth on the Ballscrew

    SGMG-13A2AB
    Thanks MACTEC
    If you have any info you can provide on the transmission thread I started, it would be appreciated.
    Marty



  4. #4
    Member
    Join Date
    Jan 2005
    Location
    USA
    Posts
    10313
    Downloads
    0
    Uploads
    0

    Default Re: TC Series Yaskawa Motors on Z

    Quote Originally Posted by Marty_Escarcega View Post
    Thanks MACTEC
    If you have any info you can provide on the transmission thread I started, it would be appreciated.
    Marty
    If you are loosing oil you can replace the seal at the bottom, they can be run without the Transmission if you don't need it, there are parameters to change a little wiring and the special motor pulley to change, I have not done any of this work for a long time my business friend still has parts I don't think there are any new gearboxes left I think the last one was sold a few months ago there will possibly be some gear box parts though

    Mactec54


  5. #5
    Member
    Join Date
    Dec 2009
    Location
    USA
    Posts
    482
    Downloads
    0
    Uploads
    0

    Default Re: TC Series Yaskawa Motors on Z

    Quote Originally Posted by mactec54 View Post
    If you are loosing oil you can replace the seal at the bottom, they can be run without the Transmission if you don't need it, there are parameters to change a little wiring and the special motor pulley to change, I have not done any of this work for a long time my business friend still has parts I don't think there are any new gearboxes left I think the last one was sold a few months ago there will possibly be some gear box parts though
    Gear box has to come off for the seal. I just got the oil today. I'm going to fill the box and see what happens. Run a warm up cycle and then start shifting gears and see if it can shift ok.
    If not, I may just remove the gear box. If your friend has the pulley and belt number that would be helpful.
    There is an off chance I know where a gear box is...

    I will be upgrading the control in the next couple of months. Going from DC Brush Servos to AC servos and Centroid Control. Doing all the prep work now....

    Marty



  6. #6
    Member
    Join Date
    Jan 2005
    Location
    USA
    Posts
    10313
    Downloads
    0
    Uploads
    0

    Default Re: TC Series Yaskawa Motors on Z

    Quote Originally Posted by Marty_Escarcega View Post
    Gear box has to come off for the seal. I just got the oil today. I'm going to fill the box and see what happens. Run a warm up cycle and then start shifting gears and see if it can shift ok.
    If not, I may just remove the gear box. If your friend has the pulley and belt number that would be helpful.
    There is an off chance I know where a gear box is...

    I will be upgrading the control in the next couple of months. Going from DC Brush Servos to AC servos and Centroid Control. Doing all the prep work now....

    Marty
    I will check to see if he has the pulleys or part numbers

    Mactec54


  7. #7
    Member
    Join Date
    Dec 2009
    Location
    USA
    Posts
    482
    Downloads
    0
    Uploads
    0

    Default Re: TC Series Yaskawa Motors on Z

    Quote Originally Posted by mactec54 View Post
    I will check to see if he has the pulleys or part numbers
    Hi Mactec,
    Seems as though with the gearbox filled up, its not missing anymore shifts. I have to test it some more...after over a week the oil level is still in the same place on the sight glass. Don't see any oil under the gear box in the drive belt well. Wondering if the previous owners ever checked it.
    I'd still be interested what it would take to remove the transmission, if I so choose and direct drive the spindle. The spindle motor seems to indicate its an 8000rpm motor. I am wondering if the motor pulley is 1:1 with the spindle or slightly smaller.

    Thanks
    Marty



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

TC Series Yaskawa Motors on Z

TC Series Yaskawa Motors on Z

TC Series Yaskawa Motors on Z