TC22 ( Torq Cut 22 ) Probe. ( Wildhorse Inivations ) - Page 4


Page 4 of 4 FirstFirst 1234
Results 61 to 65 of 65

Thread: TC22 ( Torq Cut 22 ) Probe. ( Wildhorse Inivations )

  1. #61
    Member
    Join Date
    Feb 2008
    Location
    USA
    Posts
    8
    Downloads
    0
    Uploads
    0

    Default Re: TC22 ( Torq Cut 22 ) Probe. ( Wildhorse Inivations )

    Hi, like others here, I have a Torq-Cut 22 with a DX-32 control and a Wildhorse probe. The probe works electromechanically - it will touch a surface and record a point. I cannot figure out how to enter a useful tip diameter, though, and if that information is in this thread, I missed it. When I call up a tool # and install the probe, say #24, and give that # a diameter in the tool table, the display shows "probe" and the diameter following it. However, I seem to be able to put any number in that field without affecting the location of a probed point. I also tried entering a diameter in the appropriate field in a Geometry calculation and then going back to probing from the jog menu - again, no effect on the measured point... Any ideas?

    TIA!

    Mark



  2. #62
    Member
    Join Date
    Feb 2008
    Location
    USA
    Posts
    8
    Downloads
    0
    Uploads
    0

    Default Re: TC22 ( Torq Cut 22 ) Probe. ( Wildhorse Inivations )

    Hi, forhire - I tried to reply to you and got the following:

    "forhire has exceeded their stored private messages quota and cannot accept further messages until they clear some space."

    Thanks,

    Mark



  3. #63
    Member
    Join Date
    Dec 2005
    Location
    US
    Posts
    462
    Downloads
    0
    Uploads
    0

    Default Re: TC22 ( Torq Cut 22 ) Probe. ( Wildhorse Inivations )

    Quote Originally Posted by Mark McDade View Post
    Hi, forhire - I tried to reply to you and got the following: "forhire has exceeded their stored private messages quota and cannot accept further messages until they clear some space."
    CNCZone has a very small inbox allocation. I sent you a PM with the URL for the software and manual.



  4. #64
    Member
    Join Date
    Feb 2005
    Location
    USA
    Posts
    78
    Downloads
    0
    Uploads
    0

    Default Re: TC22 ( Torq Cut 22 ) Probe. ( Wildhorse Inivations )

    The DX32 control has some parameters for the probe behavior. "Post Hit Continuation" and "Back Off Distance" which you might need to tune for your probe. I haven't fooled with these yet since I haven't bought a probe yet



  5. #65
    Member
    Join Date
    Feb 2008
    Location
    USA
    Posts
    8
    Downloads
    0
    Uploads
    0

    Default Re: TC22 ( Torq Cut 22 ) Probe. ( Wildhorse Inivations )

    Quote Originally Posted by arsenix View Post
    The DX32 control has some parameters for the probe behavior. "Post Hit Continuation" and "Back Off Distance" which you might need to tune for your probe. I haven't fooled with these yet since I haven't bought a probe yet
    There are three, 014, 015 and 016. I have played around with 15 and 16 and they don't seem to do anything (14 is probing speed and I didn't change it). I'm still puzzled that there doesn't seem to be a parameter or input field that allows compensation for probe diameter...



Page 4 of 4 FirstFirst 1234

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

TC22 ( Torq Cut 22 ) Probe.  ( Wildhorse Inivations )

TC22 ( Torq Cut 22 ) Probe.  ( Wildhorse Inivations )

TC22 ( Torq Cut 22 ) Probe.  ( Wildhorse Inivations )