Newbie Spiral Milling


Results 1 to 14 of 14

Thread: Spiral Milling

  1. #1
    Member
    Join Date
    Aug 2005
    Location
    USA
    Posts
    176
    Downloads
    0
    Uploads
    0

    Default Spiral Milling

    I have V28. I want to mill the perimeter of a part. I want to spiral down on outside instead of stepping down.

    How do I do this in V28

    Rob

    Similar Threads:


  2. #2
    Community Moderator Jim Dawson's Avatar
    Join Date
    Dec 2013
    Posts
    5717
    Downloads
    0
    Uploads
    0

    Default Re: Spiral Milling

    I don't use BobCad but I think I can give you a generic answer. I am assuming BobCad has spiral (angle?) lead in capability. Set your DOC to full depth, and set a shallow lead in angle. Then look at the tool path, adjust the angle as needed to get the approximate stepdown per pass that you want.

    Jim Dawson
    Sandy, Oregon, USA


  3. #3
    Registered
    Join Date
    Oct 2012
    Location
    USA
    Posts
    2
    Downloads
    0
    Uploads
    0

    Default Re: Spiral Milling

    Quote Originally Posted by artracing View Post
    I have V28. I want to mill the perimeter of a part. I want to spiral down on outside instead of stepping down.

    How do I do this in V28

    Rob
    HI there..I have BC/ V29 no outside spiral only Contour Ramping...
    Inside Pocket has spiraling.....



  4. #4
    Member
    Join Date
    Aug 2005
    Location
    USA
    Posts
    176
    Downloads
    0
    Uploads
    0

    Default Re: Spiral Milling

    That might be a creative way to do it.
    I’ll try
    Thanks Jim


    Rob



  5. #5
    Member
    Join Date
    May 2013
    Location
    USA
    Posts
    701
    Downloads
    0
    Uploads
    0

    Default Re: Spiral Milling

    Quote Originally Posted by artracing View Post
    I have V28. I want to mill the perimeter of a part. I want to spiral down on outside instead of stepping down.

    How do I do this in V28

    Rob
    2 Axis -- Pattern -- Contour Ramping

    Attached Thumbnails Attached Thumbnails Spiral Milling-contour-ramping-jpg  


  6. #6
    Member
    Join Date
    Aug 2005
    Location
    USA
    Posts
    176
    Downloads
    0
    Uploads
    0

    Default Re: Spiral Milling

    Yes. You are right. I noticed the profile finish doesn’t have contour ramping. Wonder why.



  7. #7
    Member
    Join Date
    Apr 2009
    Location
    usa
    Posts
    3376
    Downloads
    0
    Uploads
    0

    Default Re: Spiral Milling

    Quote Originally Posted by artracing View Post
    Yes. You are right. I noticed the profile finish doesn’t have contour ramping. Wonder why.
    Probably because in a finish pass it is usually best to go full depth so you don't have tooling marks.
    Tool Pressure comes to mind (spring)
    Keeping the tool at one constant level,,,your cut might even be a few tenths of a thousand tapered,but it will be consistent.
    A few tenths at a contour tool path will show



  8. #8
    Member
    Join Date
    Aug 2005
    Location
    USA
    Posts
    176
    Downloads
    0
    Uploads
    0

    Default Re: Spiral Milling

    Very true but there is a problem side milling 2.6 tall piece in one shot. Unless you have a 3” tall carbide mill that’s in the $300 range. Jim Sawson here showed you can use cheaper mill and spiral down. I did this finish cut with 4 flute and it was almost mirror finish



  9. #9
    Member
    Join Date
    May 2013
    Location
    USA
    Posts
    701
    Downloads
    0
    Uploads
    0

    Default Re: Spiral Milling

    Quote Originally Posted by artracing View Post
    Very true but there is a problem side milling 2.6 tall piece in one shot. Unless you have a 3” tall carbide mill that’s in the $300 range. Jim Sawson here showed you can use cheaper mill and spiral down. I did this finish cut with 4 flute and it was almost mirror finish
    In the next window after contour ramping in parameter setting the -- depth per pass / depth of cut makes in easy



  10. #10
    Member
    Join Date
    Aug 2005
    Location
    USA
    Posts
    176
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by RAF. View Post
    In the next window after contour ramping in parameter setting the -- depth per pass / depth of cut makes in easy
    Yes, very likely use it all the time now.
    Need to use it on 2” hole for better precise cut. Haven’t tried that yet.



  11. #11
    Member
    Join Date
    Apr 2009
    Location
    usa
    Posts
    3376
    Downloads
    0
    Uploads
    0

    Default Re: Spiral Milling

    Quote Originally Posted by artracing View Post
    Yes. You are right. I noticed the profile finish doesn’t have contour ramping. Wonder why.
    You can just use 2 roughing contour tool paths
    2nd one with zero left for finish



  12. #12
    Member
    Join Date
    Aug 2005
    Location
    USA
    Posts
    176
    Downloads
    0
    Uploads
    0

    Default Re: Spiral Milling

    picked up V31

    Got mislead in contour milling. Plunge rate is new feed rate.
    no matter what you put in for feed rate it only follow the plung rate.



  13. #13
    Member
    Join Date
    Apr 2009
    Location
    usa
    Posts
    3376
    Downloads
    0
    Uploads
    0

    Default Re: Spiral Milling

    Quote Originally Posted by artracing View Post
    I have V28. I want to mill the perimeter of a part. I want to spiral down on outside instead of stepping down.

    How do I do this in V28

    Rob
    you could always use 3 axis wire frame
    albeit more time consuming,you would have to draw your tool path and draw leads and compensate for tool size



  14. #14
    Registered
    Join Date
    May 2008
    Location
    usa
    Posts
    244
    Downloads
    0
    Uploads
    0

    Default Re: Spiral Milling

    artracing

    this is contour ramping in 2 axis
    just enter the same feed rate for x y and z
    set feed plane just above the part something like .010-.020-.030 default is .100
    do not use a leadin
    use depth per pass and set it shallow to start (not knowing what cutter or material) cutter is critical musst plunge well
    finish pass would always be a sraight line cut
    if you want to use ramping for finish pass, just use side allowance for rgh and "0" for finish pass

    this is very useful toolpath



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Spiral Milling

Spiral Milling