Bending- and Punching Machines

Page 1 of 8 1234 ... LastLast
Threads 1 to 20 of 143

Forum: Bending- and Punching Machines

Discuss about bending and punching

  1. Amada auto index station clamp misaligned

    Started by otrotabi‎, 06-04-2024 03:20 PM
    • Replies: 4
    • Views: 1,500
    11-11-2024, 03:16 PM Go to last post
  2. K-Factor or Y-Factor list or calculator

    Started by 01f4irider‎, 11-08-2024 09:20 AM
    k-factor, list, specific, work, y-factor
    • Replies: 0
    • Views: 104
    11-08-2024, 09:20 AM Go to last post
  3. Post Turret punch machine Amada Aries-255

    Started by PopKorn85‎, 10-11-2024 07:06 AM
    amada, consumables, maintainance, punch machine, turret punch
    • Replies: 2
    • Views: 497
    10-28-2024, 01:32 PM Go to last post
  4. CNC99 Automec Error Codes FAIL 24, 65

    Started by PMFMAN‎, 06-24-2021 01:02 PM
    cnc99, codes, error, fail, support
    • Replies: 3
    • Views: 3,614
    10-22-2024, 10:38 PM Go to last post
  5. trumpf 260 NC Fault 2670 SPS TIME INHIBIT ERROR

    Started by dave82‎, 10-10-2024 10:16 AM
    • Replies: 0
    • Views: 170
    10-10-2024, 10:16 AM Go to last post
  6. Pega 244

    Started by bruce209‎, 09-21-2024 08:35 PM
    • Replies: 1
    • Views: 419
    09-23-2024, 09:01 AM Go to last post
  7. Sheet metal feature

    Started by ecope‎, 08-28-2024 11:36 PM
    • Replies: 1
    • Views: 393
    08-29-2024, 04:01 AM Go to last post
    • Replies: 0
    • Views: 589
    08-01-2024, 06:03 PM Go to last post
    • Replies: 1
    • Views: 392
    07-23-2024, 12:41 PM Go to last post
  8. Amada HFB 170-40 Issues

    Started by RickW2007‎, 12-13-2020 12:53 AM
    170-40, backgauge, hfb, machine, press
    • Replies: 10
    • Views: 5,212
    05-18-2024, 03:55 PM Go to last post
  9. Trupunch 1000 fabriwin postprocesor

    Started by frigoteknika‎, 05-02-2024 10:25 PM
    fabriwin, lot, machine, run, trupunch
    • Replies: 0
    • Views: 1,008
    05-02-2024, 10:25 PM Go to last post
  10. Tru punch 1000

    Started by frigoteknika‎, 05-02-2024 10:21 PM
    drive, hard, problem, results, tru
    • Replies: 0
    • Views: 667
    05-02-2024, 10:21 PM Go to last post
  11. amada em2510 parameter password

    Started by mickey94577‎, 04-08-2024 01:24 PM
    • Replies: 3
    • Views: 1,235
    04-10-2024, 09:24 AM Go to last post
    • Replies: 2
    • Views: 769
    04-09-2024, 06:35 PM Go to last post
  12. strippit fanuc 0-p control clamp protect

    Started by sbgo‎, 04-03-2024 06:59 PM
    • Replies: 0
    • Views: 664
    04-03-2024, 06:59 PM Go to last post
  13. Ram problem

    Started by Bohr‎, 03-01-2024 10:56 AM
    amada, make, ram, strange, vipros 255
    • Replies: 1
    • Views: 4,626
    03-04-2024, 10:28 AM Go to last post
  14. Exclamation TrumaBend V 85 S no bend on manual mode

    Started by andreistan1131‎, 01-30-2024 10:07 AM
    bend, bending, manual, mode, trumabend
    • Replies: 0
    • Views: 2,170
    01-30-2024, 10:07 AM Go to last post
  15. Amada Turret alignment

    Started by otrotabi‎, 01-19-2024 09:41 AM
    amada, cnc, punch, turret, vipros 2510
    • Replies: 0
    • Views: 2,121
    01-19-2024, 09:41 AM Go to last post
  16. CNC 99 automec

    Started by Esau B‎, 01-12-2024 07:38 PM
    automec, back, cnc, gage, inches
    • Replies: 0
    • Views: 1,918
    01-12-2024, 07:38 PM Go to last post
  17. Handling "stripping failure" alarm

    Started by otrotabi‎, 12-14-2023 07:23 AM
    punch, punching, sheet, start, stuck
    • Replies: 3
    • Views: 2,700
    12-19-2023, 06:04 AM Go to last post

Page 1 of 8 1234 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 3 users browsing this forum. (0 members & 3 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands