Need Help! AC servo spindle encoder setup mach3


Results 1 to 5 of 5

Thread: AC servo spindle encoder setup mach3

  1. #1
    Member ny_racer_xxx's Avatar
    Join Date
    Mar 2012
    Location
    USA
    Posts
    229
    Downloads
    0
    Uploads
    0

    Default AC servo spindle encoder setup mach3

    Ok, I have a griz G0704 with a chinese ac servo and driver combo. Setup as step in mach3, works flawlessly, best money spent.
    I'm trying to figure out how to setup mach3 to utilize the encoder for rpm read out and positioning for rigid tapping. I have 3 outputs for the encoder, I assume for each phase. They each have a + and - minus I assume for common and input on my board pins.

    Mach3 literature is useless, and haven't found any from google, the many different ways I've searched.

    Thanks in advance.

    CR

    Similar Threads:


  2. #2
    Member
    Join Date
    Feb 2008
    Location
    United Kingdom
    Posts
    458
    Downloads
    2
    Uploads
    0

    Default Re: AC servo spindle encoder setup mach3

    Don't quote me but my understanding is Mach3 can only handle 1 pulse per rev. from a spindle. Multiple pulses, as required for positioning screws it up - its in the manual!



  3. #3
    Member ny_racer_xxx's Avatar
    Join Date
    Mar 2012
    Location
    USA
    Posts
    229
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by kawazuki View Post
    Don't quote me but my understanding is Mach3 can only handle 1 pulse per rev. from a spindle. Multiple pulses, as required for positioning screws it up - its in the manual!
    I see there's a usb mc that can do it, and I know you can rigid tap with it. Thank you for your input though..



  4. #4
    Member
    Join Date
    Jan 2005
    Location
    USA
    Posts
    12910
    Downloads
    0
    Uploads
    0

    Default Re: AC servo spindle encoder setup mach3

    Quote Originally Posted by ny_racer_xxx View Post
    I see there's a usb mc that can do it, and I know you can rigid tap with it. Thank you for your input though..
    If your Encoder has a Z Pulse ( index Pulse ) you can use that for Threading, Mach3 control can use an Encoder input, but read only, some have used this for the readouts, so for threading the Encoder Z Pulse is all that you can use

    You would need Acorn or UCCNC control to do full Encoder Feed Back for Rigid Tapping and they also only have the ( 1 ) encoder input for Rigid Tapping

    Mactec54


  5. #5
    Member
    Join Date
    Nov 2013
    Posts
    1373
    Downloads
    0
    Uploads
    0

    Default Re: AC servo spindle encoder setup mach3

    Hi,
    I use Mach4 and have done for seven years.

    I too have an AC servo as a spindle motor and can consequently set it up as a C axis, that is to say Step/Dir, and then rigid tap by using
    regular Gcode relying on the coordination between the two axes. Most of the time my spindle is set up as voltage controlled velocity mode
    as a free running spindle, only when I want to tap does it switch to Step/Dir.

    Note that this operation relies on coordination between two axes that is provided by interpolation that is inherent in Gcode.

    This is different to what would be called rigid tapping by most people in the industry. They refer to rigid tapping as the Z axis is synchronised, or perhaps better understood as,
    'Z axis rotates directly commensurate with the encoder on the spindle'.This in turn requires that the Z axis Step/Dir signals be generated in realtime synchronism
    with the encoder signals. Mach3 and Mach4 run on Windows platforms and require a 'buffered' (delayed) control, ie cannot be realtime. For rigid tapping, using the
    industry standard use of the term, must be done by the motion controller, because the motion controller alone can be realtime.

    I understand Mach4 does have a G84 rigid tapping command but requires support from the motion controller, and to my knowledge my ESS does not
    support it.

    Mach3 and Mach4 both handle single point lathe threading but rigid tapping is another step beyond.

    The spindle rotation must be synchronised with the Z axis, very much the same as lathe threading, but then it must decelerate to a stop and then reverse all the while
    maintaining perfect synchronism with the Z axis, so tougher again than lathe threading.

    Despite the fact that Mach (3 or 4), nor my motion controller can natively support rigid tapping, I have got it to work....and would guess that you could too. Its been some
    years since I've used Mach3 and so cannot be sure that you could do it with Mach3, but I can with Mach4.

    Craig.



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

AC servo spindle encoder setup mach3

AC servo spindle encoder setup mach3

AC servo spindle encoder setup mach3