Avid CNC


Page 1 of 44 123411 ... LastLast
Threads 1 to 20 of 863

Forum: Avid CNC

Discuss Avid CNC here!

  1. Idea Adding mass (wieght) to machine bed???

    Started by Lbrown‎, 06-28-2022 12:33 PM
    avid cnc mods, cnc, diy, mass, rigidty
    • Replies: 3
    • Views: 107
    Yesterday, 11:12 AM Go to last post
    • Replies: 4
    • Views: 199
    06-27-2022, 02:15 PM Go to last post
  2. Newbie- Dual cnc and plasma machine build

    Started by dukey008‎, 06-26-2022 09:46 AM
    5x10, cnc, cutting, machine, plasma
    • Replies: 2
    • Views: 96
    06-26-2022, 11:08 PM Go to last post
  3. Need Help!- Shake / Jerk / Stutter when changing direction

    Started by dempseyrob‎, 06-26-2022 10:17 AM
    avid, cnc, jerk, machine, shake
    • Replies: 2
    • Views: 124
    06-26-2022, 10:49 PM Go to last post
  4. New Machine Build- Avid Z stage, Clearpath motor and a 22 pound Spindle. Z drops when powered off.

    Started by Old_Phart‎, 01-04-2020 01:41 PM
    2 Pages
    1 2
    • Replies: 37
    • Views: 3,863
    06-25-2022, 01:30 AM Go to last post
  5. Need Help!- Multiple WCS and Manual Tool Changes

    Started by sirklezero‎, 02-27-2022 06:05 PM
    cam, cnc, manufacturing, offset, tool
    • Replies: 2
    • Views: 319
    06-25-2022, 01:02 AM Go to last post
  6. Mach 4 - Losing Homing

    Started by Goonk‎, 03-23-2022 11:11 PM
    • Replies: 19
    • Views: 786
    06-19-2022, 08:33 PM Go to last post
    • Replies: 9
    • Views: 462
    06-17-2022, 01:44 PM Go to last post
  7. DIY Vacuum Bed Resources I Found...

    Started by baldcaldwell‎, 06-16-2022 10:41 AM
    cnc, forum, found, resources, vacuum
    • Replies: 0
    • Views: 108
    06-16-2022, 10:41 AM Go to last post
  8. INSTALLATION of an AVID 48X48

    Started by Tomcat104‎, 05-25-2022 11:58 AM
    48x48, avid, cnc, interested, legs
    • Replies: 1
    • Views: 262
    05-30-2022, 01:03 PM Go to last post
  9. Better guide rail dust covers

    Started by Kosh‎, 05-14-2022 07:19 PM
    • Replies: 3
    • Views: 292
    05-17-2022, 12:25 PM Go to last post
  10. Need Help!- Spindle will not increase RPM

    Started by Awk121‎, 05-07-2022 04:23 PM
    • Replies: 8
    • Views: 318
    05-12-2022, 09:48 AM Go to last post
  11. Utah set up of avid cnc?

    Started by jeffwoolums‎, 05-11-2022 11:46 AM
    avid, cnc, forum, management, utah
    • Replies: 0
    • Views: 156
    05-11-2022, 11:46 AM Go to last post
  12. Newbie- Delivery Times for a Pro 4896

    Started by blakerooney‎, 05-09-2022 02:12 PM
    couple, delivery, garage, pro, weeks
    • Replies: 1
    • Views: 229
    05-09-2022, 07:23 PM Go to last post
  13. Possible CNC rebuild using Avid Components

    Started by SteveS‎, 05-03-2022 02:00 PM
    • Replies: 3
    • Views: 307
    05-04-2022, 02:52 PM Go to last post
  14. Question Need Help!- Need Technician to Service Machine in Cincinnati

    Started by micahsmearsoll‎, 04-21-2022 01:10 PM
    cnc, cut, knowledge, problem, software
    • Replies: 1
    • Views: 277
    04-27-2022, 01:54 AM Go to last post
  15. Thump from Motor when Powering On

    Started by bwiab‎, 02-06-2022 04:48 PM
    causing, check, concerned, motor, thump
    • Replies: 3
    • Views: 400
    04-20-2022, 01:47 AM Go to last post
  16. 5' x 10' pro just arrived... lots of questions

    Started by Bearhawk LSA‎, 03-21-2022 05:59 PM
    advice, cnc, dust, software, tormach
    • Replies: 5
    • Views: 518
    04-19-2022, 12:16 AM Go to last post
  17. Need Help!- Tramming inconsistencies at each end in both x & y directions

    Started by MplsArtist‎, 04-08-2022 08:08 PM
    • Replies: 10
    • Views: 427
    04-14-2022, 07:33 PM Go to last post

Page 1 of 44 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 10 users browsing this forum. (0 members & 10 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands