Avid CNC


Page 1 of 43 123411 ... LastLast
Threads 1 to 20 of 855

Forum: Avid CNC

Discuss Avid CNC here!

  1. Mach 4 - Losing Homing

    Started by Goonk‎, 03-23-2022 11:11 PM
    • Replies: 10
    • Views: 441
    Today, 12:38 AM Go to last post
  2. Better guide rail dust covers

    Started by Kosh‎, 05-14-2022 07:19 PM
    • Replies: 3
    • Views: 155
    Yesterday, 12:25 PM Go to last post
  3. Need Help!- Spindle will not increase RPM

    Started by Awk121‎, 05-07-2022 04:23 PM
    • Replies: 8
    • Views: 260
    05-12-2022, 09:48 AM Go to last post
  4. Utah set up of avid cnc?

    Started by jeffwoolums‎, 05-11-2022 11:46 AM
    avid, cnc, forum, management, utah
    • Replies: 0
    • Views: 100
    05-11-2022, 11:46 AM Go to last post
  5. Newbie- Delivery Times for a Pro 4896

    Started by blakerooney‎, 05-09-2022 02:12 PM
    couple, delivery, garage, pro, weeks
    • Replies: 1
    • Views: 126
    05-09-2022, 07:23 PM Go to last post
  6. Possible CNC rebuild using Avid Components

    Started by SteveS‎, 05-03-2022 02:00 PM
    • Replies: 3
    • Views: 212
    05-04-2022, 02:52 PM Go to last post
  7. Question Need Help!- Need Technician to Service Machine in Cincinnati

    Started by micahsmearsoll‎, 04-21-2022 01:10 PM
    cnc, cut, knowledge, problem, software
    • Replies: 1
    • Views: 216
    04-27-2022, 01:54 AM Go to last post
  8. Thump from Motor when Powering On

    Started by bwiab‎, 02-06-2022 04:48 PM
    causing, check, concerned, motor, thump
    • Replies: 3
    • Views: 352
    04-20-2022, 01:47 AM Go to last post
  9. 5' x 10' pro just arrived... lots of questions

    Started by Bearhawk LSA‎, 03-21-2022 05:59 PM
    advice, cnc, dust, software, tormach
    • Replies: 5
    • Views: 425
    04-19-2022, 12:16 AM Go to last post
  10. Need Help!- Tramming inconsistencies at each end in both x & y directions

    Started by MplsArtist‎, 04-08-2022 08:08 PM
    • Replies: 10
    • Views: 353
    04-14-2022, 07:33 PM Go to last post
  11. Better collet wrenches?

    Started by Kosh‎, 04-11-2022 08:21 PM
    • Replies: 0
    • Views: 166
    04-11-2022, 08:21 PM Go to last post
    • Replies: 11
    • Views: 2,641
    03-25-2022, 04:52 PM Go to last post
  12. Spindle Question

    Started by honesttjohn‎, 07-18-2021 12:33 PM
    • Replies: 16
    • Views: 1,013
    03-19-2022, 05:51 AM Go to last post
  13. Torque Wrench for collet nut

    Started by Brandnewnoise‎, 03-03-2022 05:01 PM
    bit, cnc, collet, torque, torque wrench
    • Replies: 4
    • Views: 370
    03-07-2022, 09:29 AM Go to last post
  14. Avid Spoilboard Surfacing Fail

    Started by bwiab‎, 02-06-2022 12:23 AM
    • Replies: 9
    • Views: 707
    03-06-2022, 08:32 PM Go to last post
  15. Looking for 3D printed "hack" to TouchPlate

    Started by Kosh‎, 02-13-2021 07:37 PM
    • Replies: 7
    • Views: 866
    03-06-2022, 11:28 AM Go to last post
  16. Need Help!- Multiple WCS and Manual Tool Changes

    Started by sirklezero‎, 02-27-2022 06:05 PM
    cam, cnc, manufacturing, offset, tool
    • Replies: 0
    • Views: 206
    02-27-2022, 06:05 PM Go to last post
  17. Nema 34 and corner touch plate

    Started by Docwatt‎, 02-12-2022 11:40 AM
    corner, mach4, nema34, pro4896, touch
    • Replies: 1
    • Views: 397
    02-12-2022, 11:12 PM Go to last post
  18. Mach 4 / Surface Mapping Feature

    Started by recmob‎, 02-09-2022 09:43 AM
    function, mach, mapping, software, surface
    • Replies: 1
    • Views: 292
    02-09-2022, 05:11 PM Go to last post
  19. Need Help!- Smoothstepper Error returned from USB function FT_Write

    Started by Tristar500‎, 02-04-2022 08:57 PM
    2 Pages
    1 2
    • Replies: 20
    • Views: 614
    02-08-2022, 11:50 AM Go to last post

Page 1 of 43 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 5 users browsing this forum. (0 members & 5 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands