Automation Technology Products - Page 3


Page 3 of 26 FirstFirst 12345613 ... LastLast
Threads 41 to 60 of 515

Forum: Automation Technology Products

Discuss Automation Technology Products here.

  1. Problem- KL-Series Drivers, Leadshine and Similar Import Drive wiring

    Started by datac‎, 12-13-2017 06:09 PM
    dir, drives, flashcut, sense, source
    • Replies: 1
    • Views: 441
    12-15-2017, 03:35 PM Go to last post
  2. Solved stepper knocks

    Started by Dean448‎, 12-10-2017 10:52 AM
    g540, kl-6050, kl23h251-24-8b, parallel, series
    • Replies: 1
    • Views: 360
    12-10-2017, 10:59 AM Go to last post
  3. Gecko G540 vs. KL-4030 drivers (and break out board)

    Started by cncuser1‎, 11-14-2017 09:22 PM
    board, drivers, g540, gecko, kl-4030
    • Replies: 4
    • Views: 949
    12-06-2017, 07:13 PM Go to last post
  4. Sloppy

    Started by joe90023‎, 11-27-2017 09:35 PM
    • Replies: 1
    • Views: 437
    11-28-2017, 09:40 AM Go to last post
    • Replies: 6
    • Views: 1,017
    10-02-2017, 05:16 PM Go to last post
  5. Question Need Help!- "peak current" or "reference current" configuration

    Started by Djsilva2005‎, 09-27-2017 01:23 PM
    amperage, config, drivers, stepper, temperature
    • Replies: 2
    • Views: 421
    09-27-2017, 03:43 PM Go to last post
  6. Which Power Supply Do I Need

    Started by Shanghyd‎, 09-23-2017 01:07 PM
    2.8a, 425oz, motors, power, supply
    • Replies: 0
    • Views: 429
    09-23-2017, 01:07 PM Go to last post
  7. KL 4030 driver problems?

    Started by Kev‎, 08-18-2017 10:47 PM
    2 Pages
    1 2
    • Replies: 13
    • Views: 1,525
    08-30-2017, 03:28 PM Go to last post
  8. Proximity sensor wiring

    Started by Lindzr‎, 08-12-2017 10:56 PM
    • Replies: 2
    • Views: 1,415
    08-15-2017, 08:29 PM Go to last post
    • Replies: 0
    • Views: 666
    07-24-2017, 10:53 PM Go to last post
  9. C11GS - Is there an updated wiring schematic?

    Started by Azalin‎, 07-16-2017 10:50 AM
    • Replies: 2
    • Views: 515
    07-21-2017, 02:52 PM Go to last post
  10. KL-300 Noise & runout

    Started by psykhon‎, 06-10-2017 10:34 AM
    high, kl-300, noise, pitch, runout
    • Replies: 0
    • Views: 530
    06-10-2017, 10:34 AM Go to last post
  11. Kelling Dip Switch Orientation???

    Started by ny_racer_xxx‎, 03-04-2016 04:28 PM
    2 Pages
    1 2
    0=off, 1=on, kitten, set, switch
    • Replies: 12
    • Views: 2,130
    04-24-2017, 02:45 PM Go to last post
  12. Need Help!- Current Settings for KL4042D Stepper Drivers and Stepper Motors

    Started by New Lathe Man‎, 04-01-2017 07:43 PM
    current, mode, set, software, stepper
    • Replies: 0
    • Views: 549
    04-01-2017, 07:43 PM Go to last post
  13. KL-8070D Software configured mode?

    Started by beltramidave‎, 03-30-2017 10:24 PM
    configured, dip, mode, setting, software
    • Replies: 5
    • Views: 443
    03-31-2017, 11:21 AM Go to last post
  14. C10 BOB + + USS + 5056D Drivers will not turn motor

    Started by Ambico‎, 06-04-2016 12:59 PM
    • Replies: 8
    • Views: 1,135
    03-29-2017, 09:50 AM Go to last post
    • Replies: 4
    • Views: 391
    03-28-2017, 08:59 PM Go to last post
  15. Solved Sunfar E300 series VFD reset-the spindle runs once again!

    Started by newcreations‎, 03-24-2017 10:33 AM
    deep, plunge, reset, sunfar, vcarve pro
    • Replies: 0
    • Views: 804
    03-24-2017, 10:33 AM Go to last post
  16. new machine help think my breakout board is fried

    Started by skinny1965‎, 01-27-2017 11:18 AM
    board, check, cnc, set, signal
    • Replies: 0
    • Views: 704
    01-27-2017, 11:18 AM Go to last post
  17. Mach 3, C11 BOB questions.

    Started by vz58‎, 12-10-2016 11:04 AM
    c11, input, led, mach, set
    • Replies: 1
    • Views: 650
    12-11-2016, 02:31 PM Go to last post

Page 3 of 26 FirstFirst 12345613 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 3 users browsing this forum. (0 members & 3 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands