Automation Technology Products


Page 1 of 24 123411 ... LastLast
Threads 1 to 20 of 477

Forum: Automation Technology Products

Discuss Automation Technology Products here.

  1. .8k Spindle, holder, vfd combo assistance

    Started by dregalia‎, 03-28-2018 03:08 PM
    cnc, combo, kind, warranty, work
    • Replies: 0
    • Views: 164
    03-28-2018, 03:08 PM Go to last post
  2. KL-1160 spindle motor - Anyone using one of these?

    Started by rcheli‎, 01-22-2018 08:23 AM
    info, issues, kl-1160, motor, spindle motor
    • Replies: 0
    • Views: 546
    01-22-2018, 08:23 AM Go to last post
  3. Problem- Need wiring of this Breakout board and ID

    Started by Barefootboy4‎, 12-27-2017 04:49 PM
    • Replies: 0
    • Views: 333
    12-27-2017, 04:49 PM Go to last post
  4. KL- 8060 Driver problem on new conversion

    Started by rcheli‎, 12-11-2017 08:53 PM
    item#, kl-8060, motor, nema34 steppers, stepper
    • Replies: 6
    • Views: 402
    12-20-2017, 07:33 AM Go to last post
  5. Problem- KL-Series Drivers, Leadshine and Similar Import Drive wiring

    Started by datac‎, 12-13-2017 06:09 PM
    dir, drives, flashcut, sense, source
    • Replies: 1
    • Views: 229
    12-15-2017, 03:35 PM Go to last post
  6. Solved stepper knocks

    Started by Dean448‎, 12-10-2017 10:52 AM
    g540, kl-6050, kl23h251-24-8b, parallel, series
    • Replies: 1
    • Views: 157
    12-10-2017, 10:59 AM Go to last post
  7. Gecko G540 vs. KL-4030 drivers (and break out board)

    Started by cncuser1‎, 11-14-2017 09:22 PM
    board, drivers, g540, gecko, kl-4030
    • Replies: 4
    • Views: 582
    12-06-2017, 07:13 PM Go to last post
  8. Sloppy

    Started by joe90023‎, 11-27-2017 09:35 PM
    • Replies: 1
    • Views: 270
    11-28-2017, 09:40 AM Go to last post
    • Replies: 6
    • Views: 870
    10-02-2017, 05:16 PM Go to last post
  9. Question Need Help!- "peak current" or "reference current" configuration

    Started by Djsilva2005‎, 09-27-2017 01:23 PM
    amperage, config, drivers, stepper, temperature
    • Replies: 2
    • Views: 255
    09-27-2017, 03:43 PM Go to last post
  10. Which Power Supply Do I Need

    Started by Shanghyd‎, 09-23-2017 01:07 PM
    2.8a, 425oz, motors, power, supply
    • Replies: 0
    • Views: 283
    09-23-2017, 01:07 PM Go to last post
  11. KL 4030 driver problems?

    Started by Kev‎, 08-18-2017 10:47 PM
    2 Pages
    1 2
    • Replies: 13
    • Views: 1,016
    08-30-2017, 03:28 PM Go to last post
  12. Proximity sensor wiring

    Started by Lindzr‎, 08-12-2017 10:56 PM
    • Replies: 2
    • Views: 531
    08-15-2017, 08:29 PM Go to last post
    • Replies: 0
    • Views: 354
    07-24-2017, 10:53 PM Go to last post
  13. C11GS - Is there an updated wiring schematic?

    Started by Azalin‎, 07-16-2017 10:50 AM
    • Replies: 2
    • Views: 351
    07-21-2017, 02:52 PM Go to last post
  14. KL-300 Noise & runout

    Started by psykhon‎, 06-10-2017 10:34 AM
    high, kl-300, noise, pitch, runout
    • Replies: 0
    • Views: 416
    06-10-2017, 10:34 AM Go to last post
  15. Kelling Dip Switch Orientation???

    Started by ny_racer_xxx‎, 03-04-2016 04:28 PM
    2 Pages
    1 2
    0=off, 1=on, kitten, set, switch
    • Replies: 12
    • Views: 1,821
    04-24-2017, 02:45 PM Go to last post
  16. Need Help!- Current Settings for KL4042D Stepper Drivers and Stepper Motors

    Started by New Lathe Man‎, 04-01-2017 07:43 PM
    current, mode, set, software, stepper
    • Replies: 0
    • Views: 439
    04-01-2017, 07:43 PM Go to last post
  17. KL-8070D Software configured mode?

    Started by beltramidave‎, 03-30-2017 10:24 PM
    configured, dip, mode, setting, software
    • Replies: 5
    • Views: 346
    03-31-2017, 11:21 AM Go to last post
  18. C10 BOB + + USS + 5056D Drivers will not turn motor

    Started by Ambico‎, 06-04-2016 12:59 PM
    • Replies: 8
    • Views: 996
    03-29-2017, 09:50 AM Go to last post

Page 1 of 24 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 4 users browsing this forum. (0 members & 4 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands