Aspire 10.5 Rotary Axis Help,


Results 1 to 6 of 6

Thread: Aspire 10.5 Rotary Axis Help,

  1. #1
    Member
    Join Date
    Jan 2017
    Location
    United States
    Posts
    52
    Downloads
    6
    Uploads
    0

    Lightbulb Aspire 10.5 Rotary Axis Help,

    I am Tring my best to learn how to set up The Tool Paths , Roughing and Finishing Paths
    For machining Chess pieces, small statues ect, From Importing STL Models and Creating the Toolpaths.
    Need to know how to use the Settings for Optimum speed and cuts,
    Is it better to Zero Z-Axis on Surface? Or Center Of A-Axis? Things like this,,
    Also my codes are leaving a very small stick on each end of cut piece, is This NORMAL?
    This has been breaking when Changing tool for finishing pass and Re-zeroing, Also an hour and a half seems a bit too long for Roughing a little chess piece,
    I appreciate any tips and help for doing this, I'm lost as a ball in high weeds, :-)
    My stock is 1.375 round, Length of Model Cut is just under 3 inches, Like 2.980
    Cubs

    Tried to post the STL File, But was too large,,

    Similar Threads:


  2. #2
    Member
    Join Date
    Jan 2017
    Location
    United States
    Posts
    52
    Downloads
    6
    Uploads
    0

    Default Re: Aspire 10.5 Rotary Axis Help,

    Gerry,, Does the Rotary Axis have to be Wired to the Y-Axis Motor Driver? Or can it Operate properly with it's own Motor Driver?
    I have watched Videos till I'm Blue in the face, And Just can't seem to Configure My machine to Run Right With Rotary Axis,
    Tried Aspire 10.5 Code,, And Desk Proto, But The Codes are NO WHERE Near right with machine movement,
    Thanks,
    Cubs



  3. #3
    Member awerby's Avatar
    Join Date
    Apr 2004
    Posts
    5728
    Downloads
    0
    Uploads
    0

    Default Re: Aspire 10.5 Rotary Axis Help,

    If you're using DeskProto, you need to set up a rotary A axis parallel to X. It needs its own driver, separate from Y. You generally set Z and Y zeroes at the center of your part. It works without any substitution of Y axis code for A.

    You'll have to ask others about how Aspire works, but if you need help setting up your machine for DeskProto, feel free to reach out.

    [FONT=Verdana]Andrew Werby[/FONT]
    [URL="http://www.computersculpture.com/"]Website[/URL]


  4. #4
    Member
    Join Date
    Jan 2017
    Location
    United States
    Posts
    52
    Downloads
    6
    Uploads
    0

    Default Re: Aspire 10.5 Rotary Axis Help,

    Quote Originally Posted by awerby View Post
    If you're using DeskProto, you need to set up a rotary A axis parallel to X. It needs its own driver, separate from Y. You generally set Z and Y zeroes at the center of your part. It works without any substitution of Y axis code for A.

    You'll have to ask others about how Aspire works, but if you need help setting up your machine for DeskProto, feel free to reach out.

    Setting Up A- Axis parallel to X? Don't have a Clue,, Do You Mean in Mach3?
    IS that Like A Axis being a Slave to X Axis?
    Cubs



  5. #5
    Member awerby's Avatar
    Join Date
    Apr 2004
    Posts
    5728
    Downloads
    0
    Uploads
    0

    Default Re: Aspire 10.5 Rotary Axis Help,

    I just meant that the central axis of the rotary table and tailstock assembly lines up with the X axis rather than with Y and is on there straight. It's not a slave; it's independent of X and the other axes. In Mach3, all you have to do is ensure that A is defined as angular and calibrated in degrees, with an appropriate velocity and acceleration considering you're talking degrees per minute. Make sure the rotation radius is greater than zero. Here's a site that lays it out in more detail: https://marklindsaycnc.com/2018/04/2...e-rotary-axis/

    [FONT=Verdana]Andrew Werby[/FONT]
    [URL="http://www.computersculpture.com/"]Website[/URL]


  6. #6
    Member
    Join Date
    Jan 2017
    Location
    United States
    Posts
    52
    Downloads
    6
    Uploads
    0

    Default Re: Aspire 10.5 Rotary Axis Help,

    Quote Originally Posted by awerby View Post
    I just meant that the central axis of the rotary table and tailstock assembly lines up with the X axis rather than with Y and is on there straight. It's not a slave; it's independent of X and the other axes. In Mach3, all you have to do is ensure that A is defined as angular and calibrated in degrees, with an appropriate velocity and acceleration considering you're talking degrees per minute. Make sure the rotation radius is greater than zero. Here's a site that lays it out in more detail: https://marklindsaycnc.com/2018/04/2...e-rotary-axis/


    As Gomer says: " Thank ya Thank ya Thank ya, !!! Got it to do the Roughing cut on a Chess Piece, It Worked Great,
    But when I started the Finishing code, The Tabs at the ends of the chess piece are so thin, it broke out,,
    So I must Figure out how to keep more stock there,, To keep it from being so weak there,
    cubs



Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Aspire 10.5 Rotary Axis Help,

Aspire 10.5 Rotary Axis Help,