Need Help! X,Y,and Z motors will not work

Results 1 to 5 of 5

Thread: X,Y,and Z motors will not work

  1. #1
    Member clake4341's Avatar
    Join Date
    Jun 2019
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default X,Y,and Z motors will not work

    Hello all. I am totally new to this CNC world. I bought a cheap Chinese CNC I think it is a woodpecker 3018 . After I assembled and got things sliding as smoothly as I could I tried to fire it up with my laptop and controller board etc
    all I heard was the motors trying to work but all I heard was noise on all three motors. I disconnected the screw leads bars from X and Y motors and tried again with the same results. Do I have a problem with the motors or is my problem with the controller board . any help would be appreciated

    Ron

    Similar Threads:


  2. #2
    Member
    Join Date
    Jan 2005
    Location
    USA
    Posts
    1938
    Downloads
    2
    Uploads
    0

    Default Re: X,Y,and Z motors will not work

    The woodpecker board uses Grbl firmware that controls the motors. The program on your PC is just an interface for Grbl. Do you know what the Grbl settings are and can you post them here?



  3. #3
    Member clake4341's Avatar
    Join Date
    Jun 2019
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default Re: X,Y,and Z motors will not work

    Ok my settings for the GRBL cntl are as follows Com5 and 115200 . I have set the com in device manager to com5 so now what I get when I fire this up
    1- with the screw leads disconnected on both X and Y motors when I try and run them I get the whining noise but nothing turns I even tried to set the preset to 10 same results
    2- when I start the spindle at say 900 it seems to work just fine the spindle up and down work the same as X and Y lots of noise but no movement I also moved the screw lead coupling out about 1/8 inch out from motor
    same results . Now the fact that things seem like they should work tells me that the board appears to be working and maybe it's maybe a setting that's incorrect



  4. #4
    Member
    Join Date
    Jan 2005
    Location
    USA
    Posts
    1938
    Downloads
    2
    Uploads
    0

    Default Re: X,Y,and Z motors will not work

    Quote Originally Posted by clake4341 View Post
    Ok my settings for the GRBL cntl are as follows Com5 and 115200 . I have set the com in device manager to com5 so now what I get when I fire this up
    1- with the screw leads disconnected on both X and Y motors when I try and run them I get the whining noise but nothing turns I even tried to set the preset to 10 same results
    2- when I start the spindle at say 900 it seems to work just fine the spindle up and down work the same as X and Y lots of noise but no movement I also moved the screw lead coupling out about 1/8 inch out from motor
    same results . Now the fact that things seem like they should work tells me that the board appears to be working and maybe it's maybe a setting that's incorrect
    Those are not your Grbl settings The settings I'm talking about are the $$ settings



  5. #5
    Member clake4341's Avatar
    Join Date
    Jun 2019
    Posts
    3
    Downloads
    0
    Uploads
    0

    Default Re: X,Y,and Z motors will not work

    I not sure this is what you are looking for but I copied this from GRBL setting

    Attached Files Attached Files


Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

X,Y,and Z motors will not work

X,Y,and Z motors will not work

X,Y,and Z motors will not work