Russian Arduino Lead Screw Project?? - Page 5

Page 5 of 5 FirstFirst ... 2345
Results 81 to 86 of 86

Thread: Russian Arduino Lead Screw Project??

  1. #81
    Member appolaris's Avatar
    Join Date
    Jan 2020
    Posts
    8
    Downloads
    0
    Uploads
    0

    Default Re: Russian Arduino Lead Screw Project??

    Is there a published schematic or circuit diagram for the Nicholai67 adapter board
    !_ELS_V7.jpg image in the firmware archive contains schematic which must be a 100% match with the shield PCB (not sure about the encoder part though). So you can match Arduino pins to the shield pins and see what goes where. And labels on he shield PCB shall probably help a lot (I see that all connectors are labeled and numbered).



  2. #82
    Member
    Join Date
    Nov 2006
    Location
    Australia
    Posts
    58
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by appolaris View Post
    !_ELS_V7.jpg image in the firmware archive contains schematic which must be a 100% match with the shield PCB (not sure about the encoder part though). So you can match Arduino pins to the shield pins and see what goes where. And labels on he shield PCB shall probably help a lot (I see that all connectors are labeled and numbered).
    Thankyou appolaris, will check tonight.



  3. #83
    Member
    Join Date
    Nov 2006
    Location
    Australia
    Posts
    58
    Downloads
    0
    Uploads
    0

    Default

    Quote Originally Posted by appolaris View Post
    !_ELS_V7.jpg image in the firmware archive contains schematic which must be a 100% match with the shield PCB (not sure about the encoder part though). So you can match Arduino pins to the shield pins and see what goes where. And labels on he shield PCB shall probably help a lot (I see that all connectors are labeled and numbered).
    Sorry Appolaris havent gone thru it yet, but cant remember seeing a circuit diagram only a PCB layout.
    Will look tonight, after work to see if there is anything needing defining.
    Mounted a cog on a big stepper last night to drive LS via change gears to the Norton gearbox.
    How much longer are u going to be avail on this forum?



  4. #84
    Member
    Join Date
    Nov 2006
    Location
    Australia
    Posts
    58
    Downloads
    0
    Uploads
    0

    Default Re: Russian Arduino Lead Screw Project??

    Quote Originally Posted by bowcoastie View Post
    Hi Qtron,
    I haven't loaded any vs since vs 6. I am getting caught up so will be loading vs 72e or later in the next month or so. If you are only doing the lead-screw and not the cross-slide, then the lite versions seem to make sense. I would just do the full version as Appolaris says, it will be better supported.

    Regards,
    Bruce
    Hi Bruce, hope u r OK, been quiet on this thread!
    U interested in the nicholai67 adapter board.. i got some spares.



  5. #85
    Member appolaris's Avatar
    Join Date
    Jan 2020
    Posts
    8
    Downloads
    0
    Uploads
    0

    Default Re: Russian Arduino Lead Screw Project??

    Quote Originally Posted by qtronpowerson View Post
    Sorry Appolaris havent gone thru it yet, but cant remember seeing a circuit diagram only a PCB layout.
    Will look tonight, after work to see if there is anything needing defining.
    Mounted a cog on a big stepper last night to drive LS via change gears to the Norton gearbox.
    How much longer are u going to be avail on this forum?
    Hi Qtron,
    Right, there is no diagram for the shield PCB specifically, but there is that diagram which shows how Mega is connected to external components (buttons, LEDs, resistors etc.) and from there we can see what goes where (and labels on the PCB are helpful). I don't think there is anything else available (and probably not needed?).

    How much longer are u going to be avail on this forum?
    I will stay for some time, at least we shall help Bruce to translate remaining comments in the source code.



  6. #86
    Member
    Join Date
    Nov 2006
    Location
    Australia
    Posts
    58
    Downloads
    0
    Uploads
    0

    Default Re: Russian Arduino Lead Screw Project??

    Quote Originally Posted by appolaris View Post
    Hi Qtron,
    Right, there is no diagram for the shield PCB specifically, but there is that diagram which shows how Mega is connected to external components (buttons, LEDs, resistors etc.) and from there we can see what goes where (and labels on the PCB are helpful). I don't think there is anything else available (and probably not needed?).

    I will stay for some time, at least we shall help Bruce to translate remaining comments in the source code.
    Hi.Appolaris,
    Glad ur helping Bruce, I guess I may need bits of the code comments in English too so that I can tweak those calculation parts to get it working with my setup.
    I'm sure Bruce will share

    The User manual translation is not right either, but thats a big ask to do the whole thing.
    Some of it is OK, but some phrases are Google nonsense! & hard to unpick.
    Am not sure where Bruce is with it.
    Re the adapter board,
    After carefully looking at the PCB, & just finished buying connectors, switches etc, I feel more confident re this adapter board and its connections. Thankyou!



Page 5 of 5 FirstFirst ... 2345

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Russian Arduino Lead Screw Project??

Russian Arduino Lead Screw Project??

Russian Arduino Lead Screw Project??