PDA

View Full Version : PicStep Controllers



  1. PicStep useage questions
  2. Stepper rough 1 direction
  3. PICStep and the lack of updates!
  4. DigiKey Parts List for v2.1 board
  5. Picstep problems continue
  6. Picstep problems continue
  7. PICStep V4 (or how to not have to debug your own BOB but use someone elses!)
  8. PICStep Firmware V1.01
  9. Rough drive == overheating
  10. PicStep V4
  11. i've a problem in my picstep v.4 & 4 Axis PC interface ! please help me :)
  12. PICStep V1.1 Hi-Torque Firmware released!
  13. Please test this firmware with high torque
  14. A picstep clone layout, in eagle (attached)
  15. I know, I'm a noob...
  16. PICStep & HobbyCNC motors?
  17. PICstep PCB boards <where?>
  18. PIC STEP V4 - stalling
  19. PicStep And Mach3
  20. 16f627a?
  21. newbie questions
  22. direction line weirdness
  23. 48volts and the Picstep Driver
  24. connecting PICStep 4.0 to pminmo's interface...
  25. Uodate on rough steppers!
  26. Picking out a Driver bd-newbie ???
  27. Trouble getting Picstep to run...HELP Please
  28. Max voltage
  29. picstep V4 boards ( looking to buy 4 )
  30. Will this do what I want it to do?
  31. Help solving a motor problem???
  32. Pic stepper motor controllers
  33. Motor control
  34. Picstep and heat
  35. Fault in 1 of 3 PICSteps... Suggestions ?
  36. Picstep 4 Toolpath
  37. Picstep front copper backward?
  38. picstep drill sizes
  39. Picste Wierdness
  40. I'm looking to buy 3 picstep (v3.something)
  41. Picstep are Bi and Unipolar ???
  42. Disconnecting Motor
  43. Questions for pminmo
  44. Bug in PicStep - bad FW
  45. current limiting R2 & R4?
  46. New PICStep firmware available
  47. Using Picstep's PIC to microstep other driver chips.
  48. Can't find C5 and C7 (PicStep component)
  49. PICStep clone with Eagle files
  50. PICStep experience
  51. pic step can it be used with 6 wire stepper motor?
  52. Picstep stupid question
  53. Heatsinks?
  54. PicStep with Mach3 How??
  55. Hi Firmware V1.1 20MHz
  56. Change timeout
  57. So How Do I......Program the PIC
  58. More PIC trouble
  59. PicStep with USB
  60. Power Supply for PicStep
  61. PIC Step & H-Bridge
  62. Can Mach3 burn my PicStep?
  63. Setup question
  64. Fuse Selection
  65. Torque
  66. 5V for Picstep getting very hot !
  67. New guy asking basic questions.
  68. Need Help with Picstep opto output board
  69. motor changing direction by iteself using picstep
  70. Picstep opto input daughter board
  71. To many options
  72. Picstep trouble (won't move)
  73. LMD 18245 Gotcha
  74. PICStep after assembling
  75. A few questions about PICStep realisation
  76. Value for R21 to R28 Output Interface board
  77. PICstep, motor won't turn
  78. full->microstep driver
  79. PICStep question
  80. Problem Trouble with step selection on picstep
  81. Self standing PIC CNC unit
  82. Picstep working but trouble interfacing to PC
  83. Stepper shakes when it normally stand still
  84. To PicStep or not to PicStep!
  85. Build Thread Picstep DRAGON custom w/PMinMO BOB
  86. Build Thread Building PicSteps - Trying to find missing specs for the BOB
  87. Need Help! Check if my Circuit is right.PIC18F4550- USB, Stepper Motor, keypad & SD-Card..
  88. Need Help! PIC based GCode interpreter
  89. driving LMD18245
  90. PicStep Moves While Router Running Problem SORTED
  91. New PICStep firmware release V3!
  92. Files, images
  93. Need Help! Reversed Logic voltage to PICSTEP- What component to be replaced?
  94. control stepper motor driver controller L297 using Pic ????
  95. Need Help! PICSTEP Testing
  96. Cheaper but more powerfull Picstep :D
  97. PICStep not working!