Zen Toolworks

Page 1 of 3 123 LastLast
Threads 1 to 20 of 60

Forum: Zen Toolworks

Discuss Zen Toolworks products here!

  1. Zen spindle only runs in pulses

    Started by flaplante‎, 07-10-2017 01:38 PM
    delay, power, problem, spindle, zen
    • Replies: 1
    • Views: 125
    07-18-2017, 10:40 AM Go to last post
  2. stepper motor driver amps

    Started by oldcoalminer‎, 04-08-2017 11:28 PM
    4amps, 5.6amps, amps, driver, rms
    • Replies: 0
    • Views: 278
    04-08-2017, 11:28 PM Go to last post
  3. motor tuning

    Started by Rajudh‎, 12-16-2016 10:24 AM
    board, cnc, micro, motor, stepping
    • Replies: 0
    • Views: 336
    12-16-2016, 10:24 AM Go to last post
  4. Arduino Hookup

    Started by fretman_2‎, 07-19-2016 04:41 PM
    connected, enable, hookup, left, noticed
    • Replies: 1
    • Views: 488
    07-21-2016, 06:03 PM Go to last post
  5. Driver fuse

    Started by kjking‎, 05-14-2016 11:35 PM
    • Replies: 0
    • Views: 442
    05-14-2016, 11:35 PM Go to last post
  6. 12"x12"x3" $400 Build

    Started by johnckovacs‎, 07-23-2012 07:24 PM
    4 Pages
    1 2 3 4
    • Replies: 36
    • Views: 15,784
    01-02-2016, 07:56 PM Go to last post
  7. zen toolworks cnc with ramps v1.4

    Started by journeyp‎, 10-05-2015 11:44 PM
    axis, cnc, direction, pins, ramps
    • Replies: 1
    • Views: 867
    10-07-2015, 02:42 PM Go to last post
  8. Question about zen tool works f8

    Started by Dr.Laser676‎, 05-26-2015 12:29 AM
    question, frame, tool, works, zen
    • Replies: 0
    • Views: 994
    05-26-2015, 12:29 AM Go to last post
  9. Unhappy 7 by 7 Dropping pulses or ?

    Started by EWhite‎, 01-17-2014 05:42 PM
    mos, say, then
    • Replies: 9
    • Views: 2,102
    03-27-2015, 05:03 PM Go to last post
  10. Items I need to buy not included in Zenbot 4848 kit?

    Started by 007lab‎, 01-20-2015 05:24 PM
    • Replies: 8
    • Views: 2,867
    02-16-2015, 04:40 PM Go to last post
    • Replies: 3
    • Views: 1,153
    01-09-2015, 05:02 PM Go to last post
  11. question about upgradea

    Started by manakawari‎, 01-01-2015 08:08 PM
    • Replies: 1
    • Views: 934
    01-02-2015, 02:19 PM Go to last post
    • Replies: 0
    • Views: 1,084
    11-15-2014, 11:07 AM Go to last post
  12. Drawer Slide CNC

    Started by jkarisny‎, 09-10-2011 12:16 PM
    4 Pages
    1 2 3 4
    • Replies: 46
    • Views: 30,112
    08-14-2014, 04:12 AM Go to last post
  13. Stepper does not turn

    Started by dvdnhm‎, 07-26-2014 12:07 AM
    • Replies: 4
    • Views: 1,233
    07-28-2014, 05:28 AM Go to last post
  14. Newbie with problems.

    Started by tayda‎, 06-02-2014 05:29 PM
    cnc.
    • Replies: 0
    • Views: 1,226
    06-02-2014, 05:29 PM Go to last post
  15. Burned Out Dremel 4000

    Started by mjj‎, 05-22-2014 12:24 AM
    5.5mm, another, cor, down, except, its, maybe, mos, since, then, took, within
    • Replies: 5
    • Views: 2,692
    05-23-2014, 03:52 PM Go to last post
  16. Zen 12x12 CNC problems with the table

    Started by sydios‎, 04-05-2014 02:38 PM
    cnc., its, smo
    • Replies: 0
    • Views: 1,485
    04-05-2014, 02:38 PM Go to last post
  17. Correct Stepper Motor Driver Board Switch Settings

    Started by jmsiefer‎, 12-13-2013 06:35 PM
    down
    • Replies: 2
    • Views: 1,831
    01-26-2014, 11:25 PM Go to last post
  18. mach3 setting for TP6560 (7x7 kit)

    Started by joexusun‎, 12-18-2013 12:12 PM
    • Replies: 4
    • Views: 3,031
    01-24-2014, 04:56 AM Go to last post

Page 1 of 3 123 LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 4 users browsing this forum. (0 members & 4 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands