Zen Toolworks

Page 1 of 3 123 LastLast
Threads 1 to 20 of 60

Forum: Zen Toolworks

Discuss Zen Toolworks products here!

  1. Zen spindle only runs in pulses

    Started by flaplante‎, 07-10-2017 02:38 PM
    delay, power, problem, spindle, zen
    • Replies: 1
    • Views: 218
    07-18-2017, 11:40 AM Go to last post
  2. stepper motor driver amps

    Started by oldcoalminer‎, 04-09-2017 12:28 AM
    4amps, 5.6amps, amps, driver, rms
    • Replies: 0
    • Views: 310
    04-09-2017, 12:28 AM Go to last post
  3. motor tuning

    Started by Rajudh‎, 12-16-2016 11:24 AM
    board, cnc, micro, motor, stepping
    • Replies: 0
    • Views: 361
    12-16-2016, 11:24 AM Go to last post
  4. Arduino Hookup

    Started by fretman_2‎, 07-19-2016 05:41 PM
    connected, enable, hookup, left, noticed
    • Replies: 1
    • Views: 514
    07-21-2016, 07:03 PM Go to last post
  5. Driver fuse

    Started by kjking‎, 05-15-2016 12:35 AM
    • Replies: 0
    • Views: 470
    05-15-2016, 12:35 AM Go to last post
  6. 12"x12"x3" $400 Build

    Started by johnckovacs‎, 07-23-2012 08:24 PM
    4 Pages
    1 2 3 4
    • Replies: 36
    • Views: 16,076
    01-02-2016, 08:56 PM Go to last post
  7. zen toolworks cnc with ramps v1.4

    Started by journeyp‎, 10-06-2015 12:44 AM
    axis, cnc, direction, pins, ramps
    • Replies: 1
    • Views: 898
    10-07-2015, 03:42 PM Go to last post
  8. Question about zen tool works f8

    Started by Dr.Laser676‎, 05-26-2015 01:29 AM
    question, frame, tool, works, zen
    • Replies: 0
    • Views: 1,025
    05-26-2015, 01:29 AM Go to last post
  9. Unhappy 7 by 7 Dropping pulses or ?

    Started by EWhite‎, 01-17-2014 06:42 PM
    mos, say, then
    • Replies: 9
    • Views: 2,131
    03-27-2015, 06:03 PM Go to last post
  10. Items I need to buy not included in Zenbot 4848 kit?

    Started by 007lab‎, 01-20-2015 06:24 PM
    • Replies: 8
    • Views: 3,067
    02-16-2015, 05:40 PM Go to last post
    • Replies: 3
    • Views: 1,181
    01-09-2015, 06:02 PM Go to last post
  11. question about upgradea

    Started by manakawari‎, 01-01-2015 09:08 PM
    • Replies: 1
    • Views: 956
    01-02-2015, 03:19 PM Go to last post
    • Replies: 0
    • Views: 1,109
    11-15-2014, 12:07 PM Go to last post
  12. Drawer Slide CNC

    Started by jkarisny‎, 09-10-2011 01:16 PM
    4 Pages
    1 2 3 4
    • Replies: 46
    • Views: 31,092
    08-14-2014, 05:12 AM Go to last post
  13. Stepper does not turn

    Started by dvdnhm‎, 07-26-2014 01:07 AM
    • Replies: 4
    • Views: 1,258
    07-28-2014, 06:28 AM Go to last post
  14. Newbie with problems.

    Started by tayda‎, 06-02-2014 06:29 PM
    cnc.
    • Replies: 0
    • Views: 1,244
    06-02-2014, 06:29 PM Go to last post
  15. Burned Out Dremel 4000

    Started by mjj‎, 05-22-2014 01:24 AM
    5.5mm, another, cor, down, except, its, maybe, mos, since, then, took, within
    • Replies: 5
    • Views: 2,802
    05-23-2014, 04:52 PM Go to last post
  16. Zen 12x12 CNC problems with the table

    Started by sydios‎, 04-05-2014 03:38 PM
    cnc., its, smo
    • Replies: 0
    • Views: 1,514
    04-05-2014, 03:38 PM Go to last post
  17. Correct Stepper Motor Driver Board Switch Settings

    Started by jmsiefer‎, 12-13-2013 07:35 PM
    down
    • Replies: 2
    • Views: 1,865
    01-27-2014, 12:25 AM Go to last post
  18. mach3 setting for TP6560 (7x7 kit)

    Started by joexusun‎, 12-18-2013 01:12 PM
    • Replies: 4
    • Views: 3,104
    01-24-2014, 05:56 AM Go to last post

Page 1 of 3 123 LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 1 users browsing this forum. (0 members & 1 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands