USB, RS232 , PARALLEL ETC

Page 1 of 4 1234 LastLast
Threads 1 to 20 of 70

Forum: USB, RS232 , PARALLEL ETC

Discuss everything USB, RS232 , PARALLEL ETC here!

  1. Parallel Port issue - USB options?

    Started by originalsigns‎, Today 12:50 PM
    cnc, mach3, port, run, usb
    • Replies: 7
    • Views: 96
    Today, 05:52 PM Go to last post
  2. rs232 cable connection problem

    Started by BLnTCLK‎, Yesterday 02:27 AM
    cnc, meter, problem, rs232, usb
    • Replies: 0
    • Views: 111
    Yesterday, 02:27 AM Go to last post
  3. CNC ROUTER PARRALLEL PORT

    Started by painting01‎, 03-18-2017 05:23 PM
    cnc, connected, parallel port, port, working
    • Replies: 0
    • Views: 366
    03-18-2017, 05:23 PM Go to last post
    • Replies: 0
    • Views: 263
    01-30-2017, 08:49 PM Go to last post
  4. lpt1 can,t get to work

    Started by matpeet‎, 12-18-2016 06:01 AM
    drowning, lpt1, pin, stays
    • Replies: 0
    • Views: 498
    12-18-2016, 06:01 AM Go to last post
  5. SCSI

    Started by M.RISHIKESH‎, 04-24-2013 01:04 AM
    • Replies: 5
    • Views: 2,966
    11-04-2016, 11:55 AM Go to last post
  6. Traub TX 8F DNC

    Started by cnc.apps‎, 08-24-2016 11:49 AM
    dnc, error, image, procedure, traub
    • Replies: 0
    • Views: 794
    08-24-2016, 11:49 AM Go to last post
  7. Lab Volt 5600 serial/null modem cable

    Started by Goover‎, 08-17-2016 09:11 PM
    cable, connectors, lab, pin, type
    • Replies: 0
    • Views: 276
    08-17-2016, 09:11 PM Go to last post
  8. Liberty LPT pins

    Started by TVcameraman‎, 08-16-2016 05:16 PM
    cnc, liberty, lpt, lpt port
    • Replies: 0
    • Views: 353
    08-16-2016, 05:16 PM Go to last post
  9. Where is Parallel Port?

    Started by musicworld1‎, 08-13-2016 08:50 AM
    • Replies: 3
    • Views: 388
    08-13-2016, 09:54 AM Go to last post
  10. CNC USB DRIVER AND SOFTWARE TEST

    Started by ronaldocavalcan‎, 07-28-2016 09:18 PM
    cnc, ronaldo cavalcante, software, test, usb controller/driver
    • Replies: 0
    • Views: 428
    07-28-2016, 09:18 PM Go to last post
  11. EMUFDD 4.0 - Floppy HW Emulator (+USB)

    Started by blackvision‎, 11-08-2011 01:49 AM
    2 Pages
    1 2
    keep, non, since, within, [img
    • Replies: 14
    • Views: 10,153
    07-10-2016, 08:22 PM Go to last post
  12. Yasnac 2000B DB25 parallel port to tape reader cable

    Started by Redzilla‎, 06-04-2016 10:12 PM
    2000b, cable, parallel, port, software
    • Replies: 3
    • Views: 533
    06-08-2016, 09:01 AM Go to last post
  13. Newbie question

    Started by linux4cnc‎, 05-01-2016 11:33 PM
    2 Pages
    1 2
    cnc, machinist, small, board, usb
    • Replies: 15
    • Views: 950
    05-02-2016, 01:31 PM Go to last post
    • Replies: 9
    • Views: 1,033
    04-21-2016, 04:34 AM Go to last post
  14. CNC USB Motion Control

    Started by mkanney6‎, 04-09-2016 04:09 PM
    cnc, controller, parallel, port, usb
    • Replies: 1
    • Views: 687
    04-10-2016, 04:45 AM Go to last post
    • Replies: 5
    • Views: 1,123
    02-12-2016, 12:12 AM Go to last post
    • Replies: 0
    • Views: 635
    01-15-2016, 01:40 PM Go to last post
  15. Problem Loading Program - Mori Seiki MV-JR 10M

    Started by luvindaddy‎, 01-05-2016 06:34 PM
    control, error, program, set, stop
    • Replies: 0
    • Views: 637
    01-05-2016, 06:34 PM Go to last post
  16. Talking Communication ports setting on LapTop with Windows8

    Started by cnctech123‎, 12-05-2015 01:56 PM
    cnc, communication, laptop, port, software
    • Replies: 1
    • Views: 809
    12-05-2015, 07:33 PM Go to last post

Page 1 of 4 1234 LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 9 users browsing this forum. (2 members & 7 guests)

  1. OlfCNC,
  2. originalsigns

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands