I would like to start by saying sorry to everyone for being away for so long, it was unavoidable.
I am back and you can contact me on this site I will be checking it daily again. I am servicing machines again!! So hit me up
thanks
I would like to start by saying sorry to everyone for being away for so long, it was unavoidable.
I am back and you can contact me on this site I will be checking it daily again. I am servicing machines again!! So hit me up
thanks
very good, hitachi man.
can you help me with a cnc hitachi maccmatic 48v?.
i have a hitachi seiki lathe from '99. I want override the door settings so i can machine with the door open. Is there any way to do this?
Also, I have a bar puller and I want to be able to open the chuck, pull the bar out, and close the chuck while a program is running. Do I have to make any changes to the settings?
Thanks.
Hello Josh,
Unfortunately i am located in Poland, Europe and can't ask you to come over, so perhaps you can help me via e-mail.
We have Hitachi-Seiki HT-15 with Seicos M II control
The battery has been changed
Currently we have :
-battery alarm
-5022,5031,5033 alarms
-slbus table error
No manuals of any kind available
Any idea how to get rid of them??
Regards, Andrew
Hello Josh,
Unfortunately i am located in Poland, Europe and can't ask you to come over, so perhaps you can help me via e-mail.
We have Hitachi-Seiki HT-15 with Seicos M II control
The battery has been changed
Currently we have :
-battery alarm
-5022,5031,5033 alarms
-slbus table error
No manuals of any kind available
Any idea how to get rid of them??
Regards, Andrew
Hi Hitachi man,
Good day!
I have a HITACHI SEIKI VS 50 milling.(Fanuc 18M)
But the SIMENS PLC(S7-200) is bad.
Can you send me the ladder for Simens PLC .(Not PMC ladder)
Then I can change a new one.
Hi Hitachi man,
Good day!
I have a HITACHI SEIKI VS 50 milling.(Fanuc 18M)
But the SIMENS PLC(S7-200) is bad.
Can you send me the ladder for Simens PLC .(Not PMC ladder)
Then I can change a new one.
E-MAIL:CHARLES-LZF@HOTMAIL.COM
hi,
i have a hitachi seiki ht40g with a seicos A10L. I bought it in 1999. I hit feed hold during a tool change. It gave me an alarm, and I couldn't reset it, so I powered off the machine. When I powered back on, the alarm is still there. I'm getting a turret index power off (2252) alarm. Any way I can reset the turret?
thanks!
ok so i got the alarm to go away but now the tool numbers are off... if i call up tool 5, it gives me tool 8... how do i fix that?
manoj
check the micro program correctly and if you have back up of Micro ATC programe please re load it in machine If the problem persist feel free to communicate me on prabhatmishra@mail.com or on +919430737981
Hi,
When starting spindle by MDI at speed 500 rpm for boring soft jaws. Alarm No 520 appears saying "Spindle start impossible, Check door close, chuck close and center position".
Door close LED is ON, both the chuck proximity switch also ON (LED ON) i cannot find location of center position LED or proximity switch.
How to confirm about center position . Machine is Hitachi Seiki HT20SII .
I have its programming manuals but no operation manual. An help in this regard will be highly appreciated.
Regards,
Hello> I'm from Dominican Republic
I have a tri-turn model cnc 4NE-II-600,
Series # NE-42346SC. FS-NC Fanuc 3TF.
Well the point is that the machine gives me an error that is this low parity. I know how to delete it, and I also need the parameter.
I thank you beforehand.
Greetings. DUARTE VELEZ ..
hola hitachi man
tengo una hitachi seki 4ne-II-600 control fanuc FS 3TF
y me da un error parity low. por favor como resorver el errror
SALUDOS Y GRACIAS.
Duarte Velez
Has anyone heard from Josh aka Hitachi man since his last post in Sept? I would love to see some posts from him. I am looking for schematics for my VK45 mill. I want to add a 4th axis to it and need some help.
Keshka
I got a problem with a Hitachi VA-40 the Spindle drive and motor were checked by OESS and both of them checked good but every time try to stop the spindle with M05 it gives me an OCL LED alarm on the spindle drive....Any idea what this problem might be? please email me at robert@jrpm.com
Thank You
I have tried several times to contact him. No go. I created another thread looking for reliable service contacts. There seems to be many machines still in service yet very little support. I have a Seicos III in a lathe and looking for all the contacts I can find...
Dear all
I have Hitachi Seicos VM40 with controller is Micron 16 MII. Battery was dead so all data was lost. Dose anybody have all data for my machine. I'm willing to buy it
Regards