Results 1 to 5 of 5

Thread: Current Schematcs & support information

  1. #1
    Registered
    Join Date
    Jan 2006
    Location
    USA
    Posts
    295
    Downloads
    0
    Uploads
    0

    Current Schematcs & support information

    Here's a the most current information on schematics,parts lists, parts revision,etc. Current Schematic I don't believe there's a current schematic with out some errors/changes. Here the best I can do. in the original UHU drive forum, complete schematic to rev.0B, post#1652. Power stage schematic to rev.0C, post#1690, Parts modification for Under 11amps continuous & 0ver 11 amps continuous, post#1887. and finely most current parts list, in the thread "Revised Bills of Material for HP UHU Drives" is the "UHU HP Revised Parts List 9-22-09.xls‎" is the latest & most accurate parts list showing all parts revisions as of today.
    Hope this helps
    Paul


  2. #2
    Registered
    Join Date
    Jan 2006
    Location
    USA
    Posts
    295
    Downloads
    0
    Uploads
    0

    Schematic, Current rev. B + rev c for power stage

    Post #1 still is the correct information for the latest schematic support


  3. #3
    Registered
    Join Date
    Jan 2006
    Location
    USA
    Posts
    295
    Downloads
    0
    Uploads
    0

    Current Schematics

    Let's try this again. Hopefully here's the schematics for the UHU.HIGHPOWER
    PCB
    Attached Thumbnails Attached Thumbnails Current Schematcs & support information-img042.jpg   Current Schematcs & support information-img043.jpg   Current Schematcs & support information-img044.jpg   Current Schematcs & support information-img045.jpg  

    Current Schematcs & support information-img046.jpg   Current Schematcs & support information-img041.jpg  


  4. #4
    Registered
    Join Date
    Jan 2006
    Location
    USA
    Posts
    295
    Downloads
    0
    Uploads
    0

    wrong wiring on img.041.JPG, J8-J9 previous post

    I just noticed that the above drawing is labeled WRONG. see the enclosure with this post for the correct hook up. the drive shown is an old one when I was mounting the 470uF 200v capacitor on the P2 terminals due to a height clearance problems
    Attached Thumbnails Attached Thumbnails Current Schematcs & support information-img047.jpg  


  • #5
    Registered
    Join Date
    Jan 2006
    Location
    USA
    Posts
    295
    Downloads
    0
    Uploads
    0

    this is the closest to a accurate schematic 7/24/2012I

    I think the above schematic the closest to a current schematic to what we're building


  • Similar Threads

    1. Need information please
      By mrcopso146 in forum Mach Software (ArtSoft software)
      Replies: 0
      Last Post: 08-12-2009, 01:29 PM
    2. For some Information
      By Daniel_Collado in forum SpaceClaim
      Replies: 0
      Last Post: 04-27-2009, 12:05 PM
    3. Newbie- Information
      By thunderbite in forum General CAM Discussion
      Replies: 0
      Last Post: 04-07-2008, 07:09 AM
    4. need information
      By kal_pesh in forum Mastercam
      Replies: 1
      Last Post: 03-29-2008, 11:09 PM
    5. For your information...
      By Protobyte in forum Tormach Personal CNC Mill
      Replies: 5
      Last Post: 12-02-2006, 08:29 PM

    Posting Permissions


     


    About CNCzone.com

      We are the largest and most active discussion forum from DIY CNC Machines to the Cad/Cam software to run them. The site is 100% free to join and use, so join today!

    Follow us on

    Facebook Dribbble RSS Feed


    Search Engine Friendly URLs by vBSEO ©2011, Crawlability, Inc.