UHU Servo Controllers

Page 1 of 5 1234 ... LastLast
Threads 1 to 20 of 83

Forum: UHU Servo Controllers

Discuss UHU Servo Controllers here!

  1. a good question about the UHU.HP

    Started by tenmetalman‎, 08-21-2009 09:31 PM
    current draw, far
    • Replies: 3
    • Views: 1,839
    08-22-2009, 11:27 AM Go to last post
  2. Actual limit on encoder frequency

    Started by H.O‎, 07-21-2008 11:42 AM
    15 Pages
    1 2 3 4 5 ... 15
    • Replies: 283
    • Views: 31,700
    04-20-2009, 11:25 AM Go to last post
  3. Andrey's UHU HP

    Started by Andrey67‎, 05-30-2009 03:24 PM
    3 Pages
    1 2 3
    • Replies: 43
    • Views: 20,139
    10-22-2015, 04:31 AM Go to last post
  4. arduino and GRBL

    Started by BRuiz‎, 09-16-2022 06:48 PM
    • Replies: 0
    • Views: 2,779
    09-16-2022, 06:48 PM Go to last post
  5. Lightbulb Assembled UHU DC servo motor controller

    Started by visky‎, 12-04-2008 08:06 AM
    • Replies: 1
    • Views: 4,980
    12-07-2008, 04:47 AM Go to last post
  6. Ben's UHU saga

    Started by contactirfu‎, 02-10-2009 04:19 AM
    3 Pages
    1 2 3
    • Replies: 58
    • Views: 13,281
    04-05-2009, 02:56 PM Go to last post
  7. Exclamation Bidirectional Problem with UHU Board

    Started by jlobin‎, 02-01-2010 11:15 AM
    cause, not
    • Replies: 2
    • Views: 1,853
    02-04-2010, 03:16 AM Go to last post
  8. Cool blaspheme !

    Started by radiantheat‎, 10-07-2008 10:55 AM
    another, its, not, plus, say
    • Replies: 6
    • Views: 2,269
    10-07-2008, 04:59 PM Go to last post
  9. Unhappy board problem

    Started by visky‎, 12-19-2010 10:28 AM
    • Replies: 1
    • Views: 1,795
    01-03-2011, 03:55 AM Go to last post
  10. Arrow Can i use UHU Such as this ! on my Lathe Machine ?

    Started by irxplod‎, 10-21-2010 05:51 PM
    another
    • Replies: 6
    • Views: 2,357
    10-27-2010, 02:56 PM Go to last post
  11. Unhappy Can not reset UHU Servo Controller

    Started by mibo1112‎, 01-14-2010 04:36 AM
    not, then, went
    • Replies: 9
    • Views: 2,698
    02-03-2010, 05:53 AM Go to last post
  12. Smile Chips?

    Started by kirkchabot‎, 12-29-2010 07:08 PM
    • Replies: 1
    • Views: 1,701
    01-16-2011, 10:08 AM Go to last post
  13. Conclusion HP.UHU

    Started by contactirfu‎, 11-04-2008 06:53 AM
    • Replies: 1
    • Views: 2,719
    11-04-2008, 09:30 AM Go to last post
  14. Confusion on Old UHU encoder action

    Started by jlobin‎, 01-29-2010 09:48 AM
    down, goes
    • Replies: 1
    • Views: 1,620
    02-03-2010, 01:43 AM Go to last post
  15. Copley Controllers

    Started by Victorian Signs‎, 01-10-2019 07:46 AM
    • Replies: 0
    • Views: 7,721
    01-10-2019, 07:46 AM Go to last post
  16. Current Schematcs & support information

    Started by tenmetalman‎, 09-24-2009 11:02 AM
    • Replies: 5
    • Views: 10,238
    12-16-2014, 11:18 AM Go to last post
  17. Current sense problem

    Started by ifsercon‎, 08-14-2011 07:45 AM
    • Replies: 0
    • Views: 2,701
    08-14-2011, 07:45 AM Go to last post
  18. Divided by 4 Counter for 2000 pulse encoder

    Started by ahmedrehan‎, 01-29-2009 07:41 AM
    3 Pages
    1 2 3
    • Replies: 41
    • Views: 10,265
    03-28-2009, 04:10 PM Go to last post
  19. Does Anyone Have A Schematic of A UHU In Servie

    Started by bill south‎, 09-23-2009 06:07 AM
    • Replies: 4
    • Views: 2,746
    04-02-2010, 07:40 PM Go to last post
  20. Dose anyone Know If Uli is on Holiday?

    Started by ahmedrehan‎, 04-23-2009 03:58 PM
    knows, not
    • Replies: 1
    • Views: 1,906
    04-23-2009, 04:56 PM Go to last post

Page 1 of 5 1234 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 8 users browsing this forum. (0 members & 8 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands