Huanyang VFD Macro/ Plugin - Page 4

Page 4 of 32 FirstFirst 123456714 ... LastLast
Results 37 to 48 of 376

Thread: Huanyang VFD Macro/ Plugin

  1. #37
    Registered
    Join Date
    Mar 2010
    Location
    America
    Posts
    685
    Downloads
    0
    Uploads
    0

    Default Re: Hunayang VFD Macro

    Quote Originally Posted by needleworks View Post
    Ok, no problem, I'll certainly have a look at that, Ok, hopefully these are the HZ readings ?

    At 400rpm > 13.88 at 2000rpm > 69.44 at 2200rpm > 76.38

    Thanks again for your help Dan, much appreciated
    Hey needleworks, let me know how this works. It wont set anything below 400rpm, if you want that removed let me know. It will set any RPM higher so be careful. Remember to change min and max in UCCNC from 8000min 24000max to 400rpm to 2200rpm.

    The settings are based on the frequency's you provided above.

    Dan

    Needles2.zip



  2. #38
    Registered
    Join Date
    Mar 2010
    Location
    America
    Posts
    685
    Downloads
    0
    Uploads
    0

    Default Re: Hunayang VFD Macro

    I left a debugging window that will pop up with hex frequency. I removed it and replaced with Needles2 zip. Don't know if you already downloaded first 1



  3. #39
    Registered
    Join Date
    Mar 2014
    Posts
    10
    Downloads
    0
    Uploads
    0

    Default Re: Hunayang VFD Macro

    Quote Originally Posted by Dan911 View Post
    Hey needleworks, let me know how this works. It wont set anything below 400rpm, if you want that removed let me know. It will set any RPM higher so be careful. Remember to change min and max in UCCNC from 8000min 24000max to 400rpm to 2200rpm.

    The settings are based on the frequency's you provided above.

    Dan

    Needles2.zip
    Dan, you are an absolute star My mill is now working a treat ! It`s snowing heavy over here and very cold, so I only gave it a quick check but everything seems to be working fine now.

    Once again, many thanks for helping me out.



  4. #40
    Registered
    Join Date
    Mar 2010
    Location
    America
    Posts
    685
    Downloads
    0
    Uploads
    0

    Default Re: Hunayang VFD Macro

    Happy its working for you, Vmax549 written that frequency and crc check all I did was edit it to work for your mill.



  5. #41
    Registered
    Join Date
    Mar 2010
    Location
    America
    Posts
    685
    Downloads
    0
    Uploads
    0

    Default Re: Hunayang VFD Macro

    For the few that downloaded and using this plugin I have an updated version.


    HYPLUGIN version I.0002

    1. Lowered the minimum frequency setting from 8000rpm to 6000rpm
    2. Spindle speed override wasn't working and fixed.

    HY2.zip



  6. #42
    Registered
    Join Date
    Mar 2010
    Location
    America
    Posts
    685
    Downloads
    0
    Uploads
    0

    Default HYPLUGIN UPDATED VERSION 1.0003

    I have another update for this very popular plugin...LOL

    You can now control any spindle/motor through UNCCNC with a Huanyang VFD, cheap RS/485 converter and this plugin. Set up instructions included in zip.


    HYPLUGIN1.0003.zip


    HYPLUGIN version I.0003

    1. Added Frequency and RPM set up to control any spindle/motor.( Notice for geared/pulley motors, the RPM is for motor. implementing pulley ratio conversions in later version.




    HYPLUGIN version I.0002

    1. Lowered the minimum frequency setting from 8000rpm to 6000rpm
    2. Spindle speed override wasn't working and fixed.

    Last edited by Dan911; 01-18-2017 at 02:02 AM.


  7. #43
    Registered
    Join Date
    Mar 2010
    Location
    America
    Posts
    685
    Downloads
    0
    Uploads
    0

    Default Re: Hunayang VFD Macro

    I see there's a few that downloaded this plugin so I'm updating with a newer version I been using. I posted before that I would be adding actual RPM with the plugin, but once I learned its not possible to have actual RPM with this VFD or any other I decided against it, I thought it was such a waste of resources for the VFD and UCCNC. What I liked most of this plugin over the Mach3 plugins is the immediate response of the VFD and didn't want to jeopardize that.

    I did have an issue though when using spindle override, I wasn't able to see the RPM I was running just the +- %, so I added spindle RPM to "Sact" field for spindle override. You will have to change the field # from 870 to 2050 in screen edit. Instructions are included in zip file.


    HYplugin1.0004.zip

    HYPLUGIN version I.0004

    1. Added RPM for spindle override. (See instructions in Zip file).

    2. Fixed minor bug with spindle override.

    3. Fixed misprint in config window that referenced PD005 to PD004.






    HYPLUGIN version I.0003

    1. Added Frequency and RPM set up to control any spindle/motor.( Notice for geared/pulley motors, the RPM is for motor. implementing pulley ratio conversions in later version.




    HYPLUGIN version I.0002

    1. Lowered the minimum frequency setting from 8000rpm to 6000rpm
    2. Spindle speed override wasn't working and fixed.



  8. #44
    Registered
    Join Date
    Mar 2010
    Location
    America
    Posts
    685
    Downloads
    0
    Uploads
    0

    Default Re: Hunayang Plugin

    The last 2 zip files I posted were the wrong files and didn't realize it until tonight. (1.0003 and 1.0004) When saved from Visual Studios to a folder and locating with WinZip I was choosing from the wrong folder. I apologize for any inconvenience and troubles this my have caused, I cannot delete them but I'm posting the correct file below.

    HYPLUGIN 1.0005.zip



  9. #45
    Registered
    Join Date
    Sep 2016
    Posts
    8
    Downloads
    0
    Uploads
    0

    Default Re: Hunayang Plugin

    Quote Originally Posted by Dan911 View Post
    The last 2 zip files I posted were the wrong files and didn't realize it until tonight. (1.0003 and 1.0004) When saved from Visual Studios to a folder and locating with WinZip I was choosing from the wrong folder. I apologize for any inconvenience and troubles this my have caused, I cannot delete them but I'm posting the correct file below.

    Huanyang VFD Macro/ Plugin-hyplugin-1-0005-zip
    Hello Dan,

    first of all thank you for the work you put into this.
    There is a problem that i came across today trying to get your plugin to work.
    I installed the first version of it (UCCNC Version was 1.2022) which ran fine for turning the Spinde on and off but nothing else.
    I went to 1.0005 then and after setting it up it caused UCCNC to crash multiple times.
    Afterwards i checked on updates and updated UCCNC to 1.2029 to see if it would fix the issue but i had no luck.
    The plugin is in the folder but it wont even show up in the UCCNC Plugin list for some weird reason that i cant figure out at all.
    I tried removing and reinstalling the plugin of course but no luck on that. Does UCCNC blacklist plugins that cause multiple crashes in a row?
    I couldn't find anything in the documentation regarding that.

    Does anyone have any hints on how to fix this? I've been using UCCNC and Spindletalker for quite a while but i'd obviously love to have it run all in one package.

    regards
    kelevra



  10. #46
    Registered
    Join Date
    Sep 2016
    Posts
    8
    Downloads
    0
    Uploads
    0

    Default Re: Hunayang Plugin

    Hey Dan,

    first of all, thanks for all the work you put into this. Its greatly appriciated.
    Sadly ive come across a problem though.
    The plugin causes UCCNC to crash on my machine after a few random seconds or when i execute an m3.
    I dont get any error message aside from the usual "uccnc stopped working".

    The mach3 vfd plugin works fine, aswell as spindle talker.
    Maybe you can give me a hint on how to fix this.

    UCCNC 1.2029
    Asrock AM1B-ITX
    Athlon 5350
    4 gigs of ram
    Windows 7 sp2 with all available updates

    regards
    Patrick



  11. #47
    Gold Member
    Join Date
    Apr 2013
    Location
    Sweden
    Posts
    1521
    Downloads
    2
    Uploads
    0

    Default Re: Hunayang Plugin

    Quote Originally Posted by Kelevra83 View Post
    Hey Dan,

    first of all, thanks for all the work you put into this. Its greatly appriciated.
    Sadly ive come across a problem though.
    The plugin causes UCCNC to crash on my machine after a few random seconds or when i execute an m3.
    I dont get any error message aside from the usual "uccnc stopped working".

    The mach3 vfd plugin works fine, aswell as spindle talker.
    Maybe you can give me a hint on how to fix this.

    UCCNC 1.2029
    Asrock AM1B-ITX
    Athlon 5350
    4 gigs of ram
    Windows 7 sp2 with all available updates

    regards
    Patrick
    Which motion controller are you using? I suspect the crash is caused by something else, not the plugin. Perhaps noise. What happens if you start and control the spindle manually using the control panel, without the plugin? Is everything OK in that case?

    https://adapting-camera.blogspot.com
    https://www.youtube.com/channel/UC_vrAWOz5YGX6_e3qtXg3YA


  12. #48
    Registered
    Join Date
    Sep 2016
    Posts
    8
    Downloads
    0
    Uploads
    0

    Default Re: Hunayang Plugin

    Quote Originally Posted by A_Camera View Post
    Which motion controller are you using? I suspect the crash is caused by something else, not the plugin. Perhaps noise. What happens if you start and control the spindle manually using the control panel, without the plugin? Is everything OK in that case?
    Yes it works fine so far. Ive been using uccnc with spindle talker in combination for quite a while now, at least half a year or more.
    Ive never had any issues with noise e.t.c.
    The controller i'm using is the 400ETH.

    regards



Page 4 of 32 FirstFirst 123456714 ... LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

Huanyang VFD Macro/ Plugin
Huanyang VFD Macro/ Plugin