Tree


Page 1 of 25 123411 ... LastLast
Threads 1 to 20 of 494

Forum: Tree

Discuss the 2UVR and other mills from Tree Machine Tools

  1. Need Help!- Tree vmc spindle supplier

    Started by Inskeep‎, 07-18-2017 10:10 AM
    cartridges, spindle, suppliers, tree, vmcs
    • Replies: 5
    • Views: 381
    08-17-2017, 10:53 AM Go to last post
  2. Journeyman 330 connection pinout help

    Started by kemlin‎, 08-16-2017 10:41 AM
    connector, encoders, paired, run, shield
    • Replies: 0
    • Views: 59
    08-16-2017, 10:41 AM Go to last post
  3. Need Help!- Tree 4024 can't figure out how to set up A axis HELP

    Started by BlueBeard1988‎, 08-09-2017 04:12 PM
    axis, machine, pendant, selectable, tree
    • Replies: 1
    • Views: 99
    08-15-2017, 04:38 PM Go to last post
    • Replies: 0
    • Views: 138
    08-09-2017, 05:30 PM Go to last post
  4. Need Help!- Tree VMC 750

    Started by rzklb‎, 06-14-2017 11:49 AM
    alarm, axis, cable, tree, vmc
    • Replies: 1
    • Views: 276
    08-06-2017, 09:43 AM Go to last post
  5. J325 3 axis runaway on startup

    Started by Forcedinduction‎, 01-09-2015 08:55 PM
    away, control, down, drives, except, four, power, runaway, servo, went
    • Replies: 3
    • Views: 742
    08-02-2017, 04:18 PM Go to last post
  6. Tree J310 parting out

    Started by LunaSea‎, 07-17-2017 02:21 PM
    805-305-7268, funds, parts, repaired, sell
    • Replies: 0
    • Views: 102
    07-17-2017, 02:21 PM Go to last post
  7. Need Help!- THC sh-hc30

    Started by dhia‎, 07-17-2017 04:10 AM
    pressed, sh-hc30, sheet, thc, torch
    • Replies: 0
    • Views: 89
    07-17-2017, 04:10 AM Go to last post
  8. Question Need Help!- Tree vmc750 spindle cartridge

    Started by Inskeep‎, 07-16-2017 02:52 PM
    cartridge, find, finding, spindle, vmc750
    • Replies: 0
    • Views: 120
    07-16-2017, 02:52 PM Go to last post
  9. Tree 310 Baldor retrofit problems

    Started by num1bryanp‎, 06-20-2017 01:02 PM
    baldor, error, ipm, move, position
    • Replies: 0
    • Views: 333
    06-20-2017, 01:02 PM Go to last post
  10. New to me J330 and I'm totally lost looking for help

    Started by kemlin‎, 02-24-2017 02:01 PM
    2 Pages
    1 2
    • Replies: 23
    • Views: 1,388
    05-14-2017, 07:59 PM Go to last post
  11. New Machine Build- Tree vmc 750 servo info

    Started by Inskeep‎, 04-05-2017 05:40 PM
    info, machmotion, nema, new build, retrofit
    • Replies: 1
    • Views: 468
    04-06-2017, 01:26 AM Go to last post
  12. Journeyman 330 parts

    Started by kemlin‎, 03-27-2017 11:52 AM
    contact, control, ect, motors, parts
    • Replies: 0
    • Views: 286
    03-27-2017, 11:52 AM Go to last post
  13. Using AC Servo Motors

    Started by jknee2‎, 07-14-2015 10:34 PM
    • Replies: 2
    • Views: 898
    03-21-2017, 04:38 PM Go to last post
  14. Need Help!- Interlock issue

    Started by cobi‎, 03-19-2017 07:53 PM
    door, great, interlock, key, works
    • Replies: 1
    • Views: 200
    03-19-2017, 07:58 PM Go to last post
    • Replies: 0
    • Views: 239
    03-18-2017, 09:14 AM Go to last post
  15. Tree Journeyman 425 Spindle Motor for Sale

    Started by cfordyce05‎, 08-13-2015 03:18 PM
    • Replies: 2
    • Views: 1,199
    03-12-2017, 04:55 PM Go to last post
  16. Problem- J425 dynapath 20 z not referencing

    Started by crossthreads‎, 01-25-2017 09:27 AM
    fault, machine, reference, referencing, show
    • Replies: 1
    • Views: 393
    03-07-2017, 01:37 PM Go to last post
  17. Need Help!- X-AXIS runaway

    Started by cnctoolman‎, 01-02-2017 03:04 PM
    baldor, big, dianose, mho, x-axis
    • Replies: 4
    • Views: 648
    02-13-2017, 02:53 PM Go to last post
  18. Journeyman 425 spindle question

    Started by endmill1‎, 02-04-2017 04:36 PM
    interested, price, rpm, spindle, upgrading
    • Replies: 0
    • Views: 343
    02-04-2017, 04:36 PM Go to last post

Page 1 of 25 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 4 users browsing this forum. (0 members & 4 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands