Tree


Page 1 of 25 123411 ... LastLast
Threads 1 to 20 of 494

Forum: Tree

Discuss the 2UVR and other mills from Tree Machine Tools

  1. Need Help!- Baldor servo brushes

    Started by captainkirk‎, 01-08-2015 11:12 PM
    2525, 525, appriciated, baldor, baldor servo, brushes, help, motor brushes, motors, number, par, part, servo, servo motors, tree
    • Replies: 4
    • Views: 650
    Today, 11:48 AM Go to last post
  2. Need Help!- Tree vmc spindle supplier

    Started by Inskeep‎, 07-18-2017 10:10 AM
    cartridges, spindle, suppliers, tree, vmcs
    • Replies: 5
    • Views: 393
    08-17-2017, 10:53 AM Go to last post
  3. Journeyman 330 connection pinout help

    Started by kemlin‎, 08-16-2017 10:41 AM
    connector, encoders, paired, run, shield
    • Replies: 0
    • Views: 64
    08-16-2017, 10:41 AM Go to last post
  4. Need Help!- Tree 4024 can't figure out how to set up A axis HELP

    Started by BlueBeard1988‎, 08-09-2017 04:12 PM
    axis, machine, pendant, selectable, tree
    • Replies: 1
    • Views: 104
    08-15-2017, 04:38 PM Go to last post
    • Replies: 0
    • Views: 141
    08-09-2017, 05:30 PM Go to last post
  5. Need Help!- Tree VMC 750

    Started by rzklb‎, 06-14-2017 11:49 AM
    alarm, axis, cable, tree, vmc
    • Replies: 1
    • Views: 280
    08-06-2017, 09:43 AM Go to last post
  6. J325 3 axis runaway on startup

    Started by Forcedinduction‎, 01-09-2015 08:55 PM
    away, control, down, drives, except, four, power, runaway, servo, went
    • Replies: 3
    • Views: 744
    08-02-2017, 04:18 PM Go to last post
  7. Tree J310 parting out

    Started by LunaSea‎, 07-17-2017 02:21 PM
    805-305-7268, funds, parts, repaired, sell
    • Replies: 0
    • Views: 106
    07-17-2017, 02:21 PM Go to last post
  8. Need Help!- THC sh-hc30

    Started by dhia‎, 07-17-2017 04:10 AM
    pressed, sh-hc30, sheet, thc, torch
    • Replies: 0
    • Views: 92
    07-17-2017, 04:10 AM Go to last post
  9. Question Need Help!- Tree vmc750 spindle cartridge

    Started by Inskeep‎, 07-16-2017 02:52 PM
    cartridge, find, finding, spindle, vmc750
    • Replies: 0
    • Views: 122
    07-16-2017, 02:52 PM Go to last post
  10. Tree 310 Baldor retrofit problems

    Started by num1bryanp‎, 06-20-2017 01:02 PM
    baldor, error, ipm, move, position
    • Replies: 0
    • Views: 335
    06-20-2017, 01:02 PM Go to last post
  11. New to me J330 and I'm totally lost looking for help

    Started by kemlin‎, 02-24-2017 02:01 PM
    2 Pages
    1 2
    • Replies: 23
    • Views: 1,391
    05-14-2017, 07:59 PM Go to last post
  12. New Machine Build- Tree vmc 750 servo info

    Started by Inskeep‎, 04-05-2017 05:40 PM
    info, machmotion, nema, new build, retrofit
    • Replies: 1
    • Views: 470
    04-06-2017, 01:26 AM Go to last post
  13. Journeyman 330 parts

    Started by kemlin‎, 03-27-2017 11:52 AM
    contact, control, ect, motors, parts
    • Replies: 0
    • Views: 288
    03-27-2017, 11:52 AM Go to last post
  14. Using AC Servo Motors

    Started by jknee2‎, 07-14-2015 10:34 PM
    • Replies: 2
    • Views: 900
    03-21-2017, 04:38 PM Go to last post
  15. Need Help!- Interlock issue

    Started by cobi‎, 03-19-2017 07:53 PM
    door, great, interlock, key, works
    • Replies: 1
    • Views: 202
    03-19-2017, 07:58 PM Go to last post
    • Replies: 0
    • Views: 242
    03-18-2017, 09:14 AM Go to last post
  16. Tree Journeyman 425 Spindle Motor for Sale

    Started by cfordyce05‎, 08-13-2015 03:18 PM
    • Replies: 2
    • Views: 1,202
    03-12-2017, 04:55 PM Go to last post
  17. Problem- J425 dynapath 20 z not referencing

    Started by crossthreads‎, 01-25-2017 09:27 AM
    fault, machine, reference, referencing, show
    • Replies: 1
    • Views: 395
    03-07-2017, 01:37 PM Go to last post
  18. Need Help!- X-AXIS runaway

    Started by cnctoolman‎, 01-02-2017 03:04 PM
    baldor, big, dianose, mho, x-axis
    • Replies: 4
    • Views: 650
    02-13-2017, 02:53 PM Go to last post

Page 1 of 25 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 24 users browsing this forum. (0 members & 24 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands