Tree


Page 1 of 25 123411 ... LastLast
Threads 1 to 20 of 500

Forum: Tree

Discuss the 2UVR and other mills from Tree Machine Tools

  1. Kira VTC 30

    Started by m1n1m‎, 10-12-2017 06:34 PM
    4 Pages
    1 2 3 4
    • Replies: 40
    • Views: 2,317
    12-15-2017, 06:15 PM Go to last post
  2. Squaring Machine Table Tree760

    Started by tkarls‎, 12-14-2017 01:04 PM
    adjusting, machine, manual, square, table
    • Replies: 1
    • Views: 74
    12-14-2017, 08:15 PM Go to last post
  3. Servo motor for sale

    Started by cnctoolman‎, 12-12-2017 02:42 PM
    • Replies: 0
    • Views: 79
    12-12-2017, 02:42 PM Go to last post
  4. Need Help!- Tree J325 Oil Lube Meter Valve on "Z"

    Started by PeterTheWolf‎, 11-13-2017 11:01 PM
    line, meter, pss-00h, screw, valves
    • Replies: 1
    • Views: 192
    11-14-2017, 04:22 PM Go to last post
  5. Need Help!- Baldor servo brushes

    Started by captainkirk‎, 01-09-2015 12:12 AM
    2525, 525, appriciated, baldor, baldor servo, brushes, help, motor brushes, motors, number, par, part, servo, servo motors, tree
    • Replies: 6
    • Views: 1,023
    10-29-2017, 08:42 PM Go to last post
  6. Need Help!- Buying used Kira VTC30

    Started by m1n1m‎, 09-06-2017 07:48 PM
    • Replies: 3
    • Views: 578
    09-24-2017, 05:17 AM Go to last post
  7. Need Help!- Tree vmc spindle supplier

    Started by Inskeep‎, 07-18-2017 11:10 AM
    cartridges, spindle, suppliers, tree, vmcs
    • Replies: 5
    • Views: 479
    08-17-2017, 11:53 AM Go to last post
  8. Journeyman 330 connection pinout help

    Started by kemlin‎, 08-16-2017 11:41 AM
    connector, encoders, paired, run, shield
    • Replies: 0
    • Views: 120
    08-16-2017, 11:41 AM Go to last post
  9. Need Help!- Tree 4024 can't figure out how to set up A axis HELP

    Started by BlueBeard1988‎, 08-09-2017 05:12 PM
    axis, machine, pendant, selectable, tree
    • Replies: 1
    • Views: 159
    08-15-2017, 05:38 PM Go to last post
    • Replies: 0
    • Views: 240
    08-09-2017, 06:30 PM Go to last post
  10. Need Help!- Tree VMC 750

    Started by rzklb‎, 06-14-2017 12:49 PM
    alarm, axis, cable, tree, vmc
    • Replies: 1
    • Views: 350
    08-06-2017, 10:43 AM Go to last post
  11. J325 3 axis runaway on startup

    Started by Forcedinduction‎, 01-09-2015 09:55 PM
    away, control, down, drives, except, four, power, runaway, servo, went
    • Replies: 3
    • Views: 799
    08-02-2017, 05:18 PM Go to last post
  12. Tree J310 parting out

    Started by LunaSea‎, 07-17-2017 03:21 PM
    805-305-7268, funds, parts, repaired, sell
    • Replies: 0
    • Views: 191
    07-17-2017, 03:21 PM Go to last post
  13. Need Help!- THC sh-hc30

    Started by dhia‎, 07-17-2017 05:10 AM
    pressed, sh-hc30, sheet, thc, torch
    • Replies: 0
    • Views: 145
    07-17-2017, 05:10 AM Go to last post
  14. Question Need Help!- Tree vmc750 spindle cartridge

    Started by Inskeep‎, 07-16-2017 03:52 PM
    cartridge, find, finding, spindle, vmc750
    • Replies: 0
    • Views: 167
    07-16-2017, 03:52 PM Go to last post
  15. Tree 310 Baldor retrofit problems

    Started by num1bryanp‎, 06-20-2017 02:02 PM
    baldor, error, ipm, move, position
    • Replies: 0
    • Views: 401
    06-20-2017, 02:02 PM Go to last post
  16. New to me J330 and I'm totally lost looking for help

    Started by kemlin‎, 02-24-2017 03:01 PM
    2 Pages
    1 2
    • Replies: 23
    • Views: 1,482
    05-14-2017, 08:59 PM Go to last post
  17. New Machine Build- Tree vmc 750 servo info

    Started by Inskeep‎, 04-05-2017 06:40 PM
    info, machmotion, nema, new build, retrofit
    • Replies: 1
    • Views: 539
    04-06-2017, 02:26 AM Go to last post
  18. Journeyman 330 parts

    Started by kemlin‎, 03-27-2017 12:52 PM
    contact, control, ect, motors, parts
    • Replies: 0
    • Views: 345
    03-27-2017, 12:52 PM Go to last post

Page 1 of 25 123411 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 2 users browsing this forum. (0 members & 2 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands