Toyoda representative here if you have any questions

[Toyoda_Anthony]

My name is Anthony and I am an employee from Toyoda Machinery USA. CNCzone recently created a sub-forum on the site for Toyoda and because of that; I’ll be the representative to address any questions or issues you might have.

The information we gather from trade forums is very valuable to us, especially when designing machines. Having a forum such as this provides the feedback our engineers need to continue developing machines that meet the needs of consumers.

If anyone ever has any questions about any Toyoda products, parts, or service, feel free to post on here, or message me directly and I will do my best to assist you. I’m going to make the effort to check the forum multiple times a week, so hopefully we can respond to your questions promptly.

[1234567]

i sent you a pm about a spindle
thanks Dave

[1234567]

Anybody service toyoda fh-55 .Im in Brighton mi.

[powercut]

Looking for information on how to set the zero position and each pallet position on a RGV Toyoda pallet system with MC1K drives.

[titanmachining]

Hello Anthony,
I have a FA550 with a Fanuc 15m
When I give a M3 command, I get an Alarm 28 (Spindle Drive Unit Alarm) on the control and AL-15 on the spindle drive.
The control also says OT399 S-Spindle error
Where do I start testing?
Thanks,

[phix]

Hi Anthony,

I recently replaced the belleville washers on the drawbar on an FA450III. Now, the ATC gets a servo alarm when trying to remove the tool from the spindle. I believe this is caused by air in the hydraulic lines. Is there a procedure for bleeding the air out of the hydraulic lines from the arm assy to the unclamp cylinder?

Thanks
phix

[CANUK]

Something is wrong with the spindle on our fh80 but our seviveman can,t budge the motor to inspect the gears any suggestions would be appeciated.

[brucemazor]

Hi Anthony I posted a thread on communicating between a DNC system and Toyoda FA1050

My email is brucemazor@accuratefixes.com
Thanks

[sfilipiak]

Anthony,
I am in the process of converting some HUGE programs from our MAZAK over to our new Toyoda FH400. I have the conversion requirements down, but want to enable tool life check as we load our 490 tool Matrix. Now on our MAZAK I simply use the M58 command while each tool is called up, this checks and logs tool cutting time in the tool data page. Can you give me a quick example how to enable this feature on a FH400?
Thanks!
Steve

[wmpy]

Anthony or anyone that may be able to help, We purchased a 1995 FA450 in August that had been sitting, disconnected from power for a long period of time and lost all memory and parameters. We removed all the covers from the machine when it arrived with the intention of a good cleaning and review of all functions before replacing covers to make any repairs easier. The machine appears to be in above average condition but we have not been able to get the machine fully functional. In September we had a Fanuc technician come out, he was able to reload 15m control parameters and make it possible to jog all axes of the machine. The Spindle, pallet change, pallet index, tool change, tool magazine are still not functioning. We were told by an independent technician that we need the Toyoda software. We contacted Toyoda USA in Arlington Heights, IL about obtaining the software but after numerous calls and emails over a one month period they were unable to help. We decided that having a Toyoda technician would be the next step. Our service request was sent about a month ago, they have not come out, told us when they can come out and are not responding to emails.
Were looking for independant service, or anyone with a similar FA450, or any info or knowledge that will point us in the right direction, because we are stuck.

Thanks, West Machine Products

[ayman_mok]

Hi Anthony I have a 4 driver no MC1K-030 from Toyoda I thinking to use this driver for my CNC machine . is that one suitable or not ? if so what the complete configurations for that driver and what the suitable servo motor can I use ?
thanks
Ayman Mokhtar

[ayman_mok]

Dear
ayman_mok@yahoo.com