Search:


Tag: voltage

Search: Search took 0.02 seconds.

  1. Problem-Closed: Step signal not working

    Started by jrsaw27‎, 02-21-2013 11:58 PM
    2 Pages •
    1 2
    c11g, mach3, postep25, step pin, voltage
    • Replies: 19
    • Views: 701
    Last Post: 02-27-2013 06:04 PM
    by neilw20  Go to last post

    Forum:
    Mach Mill

  2. Closed: C10 Breakout board with laptop

    Started by StebQC‎, 01-10-2013 10:33 PM
    c10, parallel port, voltage
    • Replies: 7
    • Views: 979
    Last Post: 01-11-2013 06:33 PM
    by StebQC  Go to last post

    Forum:
    USB, RS232 , PARALLEL ETC

  3. Closed: Stepper motor voltage

    Started by erickmoraes‎, 10-26-2012 11:57 PM
    stepper motor, voltage
    • Replies: 3
    • Views: 398
    Last Post: 10-27-2012 04:58 PM
    by erickmoraes  Go to last post

    Forum:
    Stepper Motors and Drives

  4. Closed: TORCH HEIGHT CONTROL PROBLEM

    Started by TOMTIDWELL‎, 09-05-2012 05:14 PM
    hypertherm, thc, voltage
    • Replies: 3
    • Views: 671
    Last Post: 09-07-2012 07:57 AM
    by agelkom  Go to last post

    Forum:
    Hypertherm Plasma

  5. Closed: Power requirements, running a Chinese CNC in the US

    Started by kellesabelle‎, 02-23-2012 08:26 AM
    chinese cnc, power, usa, voltage
    • Replies: 2
    • Views: 659
    Last Post: 02-23-2012 07:41 PM
    by Al_The_Man  Go to last post

    Forum:
    Chinese Machines

  6. Closed: Stepper Squeal/Whine at higher voltage ... So close, but yet so far

    Started by Johnsnd‎, 12-03-2010 08:00 AM
    squeal, stepper, voltage, whine
    • Replies: 10
    • Views: 1,207
    Last Post: 12-12-2010 01:06 PM
    by vanjast  Go to last post

    Forum:
    General Electronics Discussion

  7. Closed: chinese drive voltage compatability

    Started by dix2111‎, 09-05-2010 11:47 AM
    chinese, drives, inverter, vfd, voltage
    • Replies: 3
    • Views: 1,183
    Last Post: 09-05-2010 01:43 PM
    by Al_The_Man  Go to last post

    Forum:
    Phase Converters and VFD

  8. Closed: help choosing DIY Build Controller

    Started by willheg‎, 12-13-2009 02:50 AM
    controller, driver, voltage 1 Attachment(s)
    • Replies: 5
    • Views: 2,107
    Last Post: 12-14-2009 02:53 AM
    by Tweakie  Go to last post

    Forum:
    Controller & Computer Solutions

  9. Closed: help required

    Started by willheg‎, 12-11-2009 12:38 AM
    board, controller, motor, question, voltage
    • Replies: 3
    • Views: 891
    Last Post: 12-14-2009 05:41 PM
    by dilbert0815  Go to last post

    Forum:
    Stepper Motors and Drives

  10. Newbie-Closed: stepper power supply?

    Started by eon‎, 03-28-2009 03:23 AM
    amps, stepper motor, voltage
    • Replies: 4
    • Views: 1,209
    Last Post: 03-29-2009 10:41 AM
    by Crevice Reamer  Go to last post

    Forum:
    Stepper Motors and Drives

  11. Newbie-Closed: help on power supply

    Started by willheg‎, 03-15-2009 03:24 AM
    driver, motor, power, voltage
    • Replies: 7
    • Views: 1,345
    Last Post: 03-22-2009 02:08 AM
    by willheg  Go to last post

    Forum:
    General Electronics Discussion

Results 1 to 11 of 11



 


About CNCzone.com

    We are the largest and most active discussion forum from DIY CNC Machines to the Cad/Cam software to run them. The site is 100% free to join and use, so join today!

Recommended Links

Quick Links

Follow us on

Facebook Dribbble RSS Feed


Search Engine Friendly URLs by vBSEO ©2011, Crawlability, Inc.