sheetcam -> Mach2 problem/question

[anthony]

my plasma table is all setup and wired, I'm using the demo versions of SheetCam and Mach2.

I've imported a DXF drawing of a really big 'washer'. 10cm diameter with 5cm hole in the center. just to watch my machine move in a circle.

problem: after loading into Mach2, my machine rapids to 0,0.. pauses, then rapids to Pierce point (the beginning of the first lead-in)

at this point, everything stops. Mach2 is still ticking the seconds away, but nothing moves. not even the DROs.

the only warning i get in Sheetcam is Zero Spindle Speed. (dont know if this is the answer to my own question, but I can't even find a spindle speed setting in sheetcam)

any ideas?
-anthony

[ger21]

Look at the bottom of the Mach2 screen, is there an error message there? could you post the first few lines of gcode where the problem occurs?

[anthony]

have continued experimenting.. choosing "Mach2" as the post processor gets things
moving, but my torch relay doesn't trigger when the actual cut begins

am using one of the output's on bobcampbell's breakout board. the LED doesn't light either.

(no torch attached yet)

-anthony

[debogus]

"the only warning i get in Sheetcam is Zero Spindle Speed"

Perhaps is rotory still active ? Disable it


Dave

[locost_cam]

Hi Anthony,

You need to use a plasma post processor if you are plasma/flame cutting. Plasma1.post is probably the best one for you.

Les

[anthony]

I just tried Plasma1 with better results (at least the file ran to completion).
still, my virtual torch is turning on at start of run and turning off at end of run.

no real torch control.
cutting even during rapids.

tried basicplasma.post, plasma1.post, and mach2.post

something i'm missing?

-anthony

[ger21]

Do you need the torch to be on for the THC to work properly?

[locost_cam]

In Mach2 have a look at the diagnostics page. Can you see the spindle(torch) output turning on and off?

Les

Originally Posted by anthony I just tried Plasma1 with better results (at least the file ran to completion). still, my virtual torch is turning on at start of run and turning off at end of run. no real torch control. cutting even during rapids. tried basicplasma.post, plasma1.post, and mach2.post something i'm missing? -anthony

[anthony]

no THC on this table yet.

i just posted some pics in the Plasma forum.

locost: haven't check on the diagnostics page, but LED on my breakoutboard (output for 'spindle') does turn on at the begining of the program.

if i'm cutting a big washer, the torch (LED) turns on to cut the inner profile, but doesnt turn off when it moves to the outter profile. i think i'm in some kind of "milling" mode. where the spindle ramps up, moves in, mills, ramps out, spins down.

-anthony

[locost_cam]

Your machine looks really good. Mine comes into the 'looks awful but gets the job done' category :-)

If you look at the G-code you should be able to see the commands to turn the torch on and off. M03 turns it on, M05 turns it off.

Something else to try. Enter m03 into the MDI box. The torch should fire. Enter M05 and the torch should stop.

Les

[anthony]

Les,
craziest thing is going on:
1. Mach2 will not toggle my torch despite M03/M05 lines
2. Mach3-Plasma will toggle my torch (same SheetCam code) but won't move my motors
3. Mach3 (again, with all the same configurations, and the same SheetCam code) just worked without a hitch! the torch turns on and off when its supposed to! (well, my LED lights up at the right time, anyway)

thanks again for all your help, can't wait to get the torch wired up.
-anthony

[locost_cam]

That's wierd. Well at least you have it running now.

Les