Encoder wiring

[dhc2beaver]

Hello all
I am new to the CNC world and thought, what a better place to learn.
I recently purchased an older Techno/Isel CNC router table and am upgrading all the electronics.

I am building a new control box with 3 Gecko G320x drivers and a PMDX-126 break out board.
The table has Techno/Isel servo motors with DRC TK731 8E21 500-B encoders.
My problem is that I cant find any specs online showing what wire is what to connect the above encoders to the new Gecko drives.

I have found some data sheets online for other DRC encoders showing the wire info and they all seem to have the same colour codes, but am a little leary to just wing it.

So I thought I would use all of your experiences.

Any help would be much appreciated.

Cheers
Wayne

Similar Threads:

• Encoder wiring
• Need Help!- Encoder wiring
• Problem- Encoder wiring
• encoder wiring ????
• Encoder wiring

[SAMI81]

Hello all
I am new to the CNC world and thought, what a better place to learn.
I recently purchased an older Techno/Isel CNC router table and am upgrading all the electronics.

I am building a new control box with 3 Gecko G320x drivers and a PMDX-126 break out board.
The table has Techno/Isel servo motors with DRC TK731 8E21 500-B encoders.
My problem is that I cant find any specs online showing what wire is what to connect the above encoders to the new Gecko drives.

I have found some data sheets online for other DRC encoders showing the wire info and they all seem to have the same colour codes, but am a little leary to just wing it.

So I thought I would use all of your experiences.

Any help would be much appreciated.

Cheers
Wayne

Any luck with this? I seemed to have the same issue, don't know how to connect the encoder to gecko!

Thanks

[Iron-Man]

Hello all
I am new to the CNC world and thought, what a better place to learn.
I recently purchased an older Techno/Isel CNC router table and am upgrading all the electronics.

I am building a new control box with 3 Gecko G320x drivers and a PMDX-126 break out board.
The table has Techno/Isel servo motors with DRC TK731 8E21 500-B encoders.
My problem is that I cant find any specs online showing what wire is what to connect the above encoders to the new Gecko drives.

I have found some data sheets online for other DRC encoders showing the wire info and they all seem to have the same colour codes, but am a little leary to just wing it.

So I thought I would use all of your experiences.

Any help would be much appreciated.

Cheers
Wayne

Hello Wayne

Try this, it should point you in the right direction.


Hope this helps,

Iron-Man

[zimbrich]

Hello Wayne

Try this, it should point you in the right direction.


Hope this helps,

Iron-Man

This is very good information, but is only for mechanical installation. I am looking for the wiring diagram for the same encoder. Unfortunately, DRC was bought out and then the parent company got bought out. So it looks like there is no information on this encoder on the Internet. Do you happen to know where any old DRC documentation might have landed?

Thanks!

[machinehop5]

This is very good information, but is only for mechanical installation. I am looking for the wiring diagram for the same encoder. Unfortunately, DRC was bought out and then the parent company got bought out. So it looks like there is no information on this encoder on the Internet. Do you happen to know where any old DRC documentation might have landed?

Thanks!

...I would be guessing but, I'll bet the color Code is the same on other DRC encoders. For example found this pdf for a TK91

[dazp1976]

This is very good information, but is only for mechanical installation. I am looking for the wiring diagram for the same encoder. Unfortunately, DRC was bought out and then the parent company got bought out. So it looks like there is no information on this encoder on the Internet. Do you happen to know where any old DRC documentation might have landed?

Thanks!

This has DRC stuff in it. Not sure if it's right but worth a browse through.
http://irtfweb.ifa.hawaii.edu/~tcs3/...der_primer.pdf