Results 1 to 11 of 11

Thread: Kid Safety

  1. #1
    Registered ToyMaker's Avatar
    Join Date
    May 2003
    Location
    United States
    Posts
    325
    Downloads
    0
    Uploads
    0

    Kid Safety

    Icky...

    OKAY HERE IS A GOOD REASON WHY KIDS DON'T NEED
    TO RUN WITH STUFF IN THEIR HANDS.

    Look at the first picture and study the marks the boy is pointing
    to, and try to guess what caused them.

    Then look at the second picture.

    Then show this to your children.




    robotic regards,

    Tom
    = = = = =
    "A reader does not live within the pages of a book;
    the pages live within the reader."
    - - Roberta Proctor
    Attached Thumbnails Attached Thumbnails Kid Safety-ouch1.jpg   Kid Safety-ouch2.jpg  


  2. #2
    Registered ToyMaker's Avatar
    Join Date
    May 2003
    Location
    United States
    Posts
    325
    Downloads
    0
    Uploads
    0
    I would rather have my kids knowing and careful than clueless and hurt.


    robotic regards,

    Tom
    = = = = =
    "The evolution of computer hardware:
    '69 Megadollars for a few bytes.
    '96 A few dollars for a Megabyte."
    - - Alan Williams


  3. #3
    Registered
    Join Date
    Jan 2006
    Location
    USA
    Posts
    2,451
    Downloads
    0
    Uploads
    0
    OUCH!!!


  4. #4
    Registered AMCjeepCJ's Avatar
    Join Date
    Aug 2005
    Location
    US
    Posts
    373
    Downloads
    0
    Uploads
    0

    Cool

    Finally, something I haven't done!!!!
    EXIT 85 Manufacturing "The best custom wheels, period" (www.exit85.com)
    Experts in low volume, highly complicated, one-off forged aluminum wheels


  • #5
    Registered AMCjeepCJ's Avatar
    Join Date
    Aug 2005
    Location
    US
    Posts
    373
    Downloads
    0
    Uploads
    0

    Wink

    .............................................YET~
    EXIT 85 Manufacturing "The best custom wheels, period" (www.exit85.com)
    Experts in low volume, highly complicated, one-off forged aluminum wheels


  • #6
    Registered thkoutsidthebox's Avatar
    Join Date
    Nov 2006
    Location
    Ireland
    Posts
    1,698
    Downloads
    0
    Uploads
    0
    Geeze...that's very harsh! You were lucky, I hate to think if it was a few inches higher.


  • #7
    Registered
    Join Date
    Dec 2007
    Location
    USA
    Posts
    7
    Downloads
    0
    Uploads
    0
    DAYUM!
    Dave
    www.industrial-clean-air.com


  • #8
    Registered
    Join Date
    Jul 2007
    Location
    USA
    Posts
    37
    Downloads
    0
    Uploads
    0
    Reminds me of the story my coworker told me about why you should walk not bike ride the scissors over to grandma's house......


  • #9
    Registered
    Join Date
    Aug 2008
    Location
    USA
    Posts
    43
    Downloads
    0
    Uploads
    0
    Holy cow... I guess I'll be switching over too plastic 4 my kids


  • #10
    Registered
    Join Date
    Aug 2008
    Location
    india
    Posts
    16
    Downloads
    0
    Uploads
    0
    Oh My GOD....


    thats one accident that is not likely to happen out here.

    It may be unhealthy to use our fingers for eating , but it sure is SAFER !!
    MJM


  • #11
    Registered mc-motorsports's Avatar
    Join Date
    Feb 2007
    Location
    USA
    Posts
    1,084
    Downloads
    0
    Uploads
    0
    Whoa! I couldn't really see the second pic in the thumbnail. When I clicked on it, it scared me! YUCK! I would have passed out if I would have seen that happen in front of me...


  • Similar Threads

    1. Safety Pet Peeves....
      By hardmill in forum Safety Zone
      Replies: 48
      Last Post: 12-03-2011, 12:27 PM
    2. Help Please? [Safety Concern]
      By Xero Ryuu in forum General Laser Engraving & Cutting Machine Discussion
      Replies: 8
      Last Post: 09-13-2007, 06:37 PM
    3. The truth about Safety...
      By ImanCarrot in forum Safety Zone
      Replies: 12
      Last Post: 05-19-2007, 12:45 PM
    4. Laser safety
      By smartcut in forum General Laser Engraving & Cutting Machine Discussion
      Replies: 0
      Last Post: 11-12-2006, 03:29 PM
    5. Safety concerns
      By Laff Riot in forum General Laser Engraving & Cutting Machine Discussion
      Replies: 2
      Last Post: 10-17-2006, 08:56 AM

    Posting Permissions


     


    About CNCzone.com

      We are the largest and most active discussion forum from DIY CNC Machines to the Cad/Cam software to run them. The site is 100% free to join and use, so join today!

    Follow us on

    Facebook Dribbble RSS Feed


    Search Engine Friendly URLs by vBSEO ©2011, Crawlability, Inc.