How fast is your homemade CNC? - Page 6


View Poll Results: How fast can your Homemade CNC cut?

Voters
599. You may not vote on this poll
  • less than 10 IPM (4.2mm/s)

    45 7.51%
  • 10-50 IPM (4.2 - 21 mm/s)

    181 30.22%
  • 50-100 IPM (21-42 mm/s)

    141 23.54%
  • 100 - 300 IPM (42 - 127 mm/s)

    138 23.04%
  • 300 - 600 IPM (127 - 254 mm/s

    50 8.35%
  • faster than 600 IPM (254 mm/s)

    44 7.35%
Page 6 of 6 FirstFirst ... 3456
Results 61 to 64 of 64

Thread: How fast is your homemade CNC?

  1. #61
    Registered
    Join Date
    Apr 2013
    Location
    Sweden
    Posts
    1464
    Downloads
    2
    Uploads
    0

    Default Re: How fast is your homemade CNC?

    Quote Originally Posted by linkreincarnate View Post
    what are your specs for that machine?
    The most up to date specs look something like this:

    Footprint (total area it is occupying in the room): 750 x 650mm
    Table height from floor: 890mm
    Y table size: 450 x 300mm
    Weight of Y: 17,5kg
    Working area: 310 x 270mm
    Weight of X-beam: 13,7kg
    Size of the X-beam (height x width): 500 x 540mm
    Size of Z: 350 x 150 mm
    Weight of Z: 8.5kg
    Z clearance from table top: 135mm
    Maximum speed: 8000mm/min
    Maximum acceleration: 700mm/s/s
    Stepper motor data: NEMA23 2.7V/phase, 3A, 1.6uh, 0.9 Ohm/phase
    Stepper motor driver: DQ542MA
    Stepper drivers PSU: 44VDC unregulated supply, based on a thoroidal transformer
    Motion controller: UC300ETH from CNC Drive
    Spindle motor: 400Hz, 24,000 RPM 65mm diameter air cooled 1.5kW spindle
    Spindle motor power supply: Bosch Rexroth EFC 5610 VFD
    Spindle control via Modbus communication
    CNC software: UCCNC from CNC Drive

    I think the above is pretty accurate. I am making changes all the time since it is a DIY CNC of my own design. Note that axis weights are only approximate (parts measured before installation) and the weight does not include the steppers and wiring.

    https://adapting-camera.blogspot.com
    https://www.youtube.com/channel/UC_vrAWOz5YGX6_e3qtXg3YA


  2. #62
    Registered
    Join Date
    Jan 2017
    Location
    Latvia
    Posts
    7
    Downloads
    0
    Uploads
    0

    Default Re: How fast is your homemade CNC?

    Is it possible above 200 ipm with 5 tpi with a stepper system.



  3. #63
    Registered CitizenOfDreams's Avatar
    Join Date
    Nov 2012
    Location
    USA
    Posts
    387
    Downloads
    0
    Uploads
    0

    Default Re: How fast is your homemade CNC?

    Quote Originally Posted by bewerbung View Post
    Is it possible above 200 ipm with 5 tpi with a stepper system.
    Absolutely. The rotational speed at 200 ipm would be 1 000 RPM; some steppers are capable to turn almost twice as fast with enough torque left.



  4. #64
    Registered
    Join Date
    Apr 2004
    Location
    Michigan
    Posts
    634
    Downloads
    0
    Uploads
    0

    Default How fast is your homemade CNC?

    Quote Originally Posted by bewerbung View Post
    Is it possible above 200 ipm with 5 tpi with a stepper system.
    I'm running 5tpi ballscrews about 1200rpm. I clocked them at 1500rpm but backed it down a bit. 270oz-in, gecko201, 56volt PS.

    The ballscrew are ground NSK about 25mm diameter.


    Speed test when I first put the machine together. 1500rpm, 300ipm



Page 6 of 6 FirstFirst ... 3456

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands

How fast is your homemade CNC?
How fast is your homemade CNC?