5 x 10 table for plasma / tourch / router - project

[ajclay]

Hello All,

I've been working on my project for about 6 months and I'm almost ready to start connecting the wires to the servo motors. It's been a real time consuming project. Those ads saying you can build one in a week or so are just trying to suck you in to buy their products in my opinion. I've been keeping a log on part numbers, where they came from, and cost. That's the hardest part of building a machine is coming up with a design and figuring out where and what to purchase.

I've used ideas from a lot of different machines, some from cnczone and other production machines.

Also, have an on going set of plans I've drawn in AutoCAD. I'd be willing to share if anyone is interested. The drawing is not 100% but its close. As the parts are needed I draw and update my final drawing.

This is an entry level machine. It is all I can do with the tools available and my knowledge of machine work. Also, I'm trying to use available materials that aren't hard to find. Why make it harder than what it already is?

I'm sure when it comes to getting the software and controler to work will be another big learning curve. I'm just taking it one step at a time.

Thanks for reading.

ajclay

[rpage]

Sounds interesting. I would love to see your plans. You build this table out of steel I would assume since you list it as plasma. I have a small 4 x 4 plasma table and have been thinking about a 5 x 10. Have any pictures you can post of your machine? How about cost estimates?

Congrats on almost being done!

Rick

[ajclay]

Rick,

I put the plans on my internet server for you to download. They are in AutoCAD v2000 format. I'm currently redrawing the project with Autodesk Inventor to make a real set of 3d plans. Understand, these plans are not 100%, it's project in progress. You'll have to know the bascis in AutoCad to really use the plans. Moving things around make it hard to put a lot of dimensions, so you'll have to check that as needed.

http://members.cox.net/ajclay/project_2-16-08.zip

If you want to download photos of the project, change the last part of the address to numbers like below, and to a .jpg file extension.

http://members.cox.net/ajclay/001.jpg

Currently 001.jpg - 049.jpg photos on site.

The cost is almost to the point where I've stopped adding. I'd say when I'm though with the basic machine, no plasma torch, I'm going to be in the neighborhood of $6000.00

Take a look at the plans / photos and I'll fill in the blanks. As with any project I can only wright down so much info. Some things slip through the cracks.

Aj

[Weldtutor]

Originally Posted by ajclay I put the plans on my internet server for you to download.

Good to see the start of another great looking project log.

Your plans are sure to be popular & inspirational for others wanting to begin a CNC plasma table.

I'll be following your build as you progress.

[ajclay]

Weldtutor,

I worked on the plans for a few months before I cut the first piece of metal. Should have seen what I started out with. I'm a firm believer in “if you can draw it, you can build it”. There is a lot of truth in that statement.

Now I’m to the point on making a few small parts that I have to measure the placement on the machine, then draw and make them. I just couldn’t visualize some things till I got there. I could only think so far ahead.

I did use a couple of techniques in checking machine straightness that really haven’t been discussed much, straight wire, or wire sag. This allowed me to get the rails within a real plus/minus .0025 in 12 ft. Accuracy is very important in building a machine. That’s one reason why most all my machine is bolted together and not welded. The parts in most cases can be shimmed to get the desired results.

Thanks for your interest,

Aj

[millman52]

Impressive job. Looks like your machining skills are well up to par. I certainly understand 100% the time you have invested there. I too spent many hours in the machine shop on my table. I can tell by viewing your photos you have more hours invested than I. The end result will be worth it though.

I am using Ox/Fuel on mine. I am now burning many holes that I used to drill. I do get round holes, very crisp square corners & can hold very tight tolerances. Way better than I imagined. Better by a wide margin than I could ever hope to get from any of the 3 steel suppliers I use. I'm sure they have state of the art "MEGA BUCK" machines also.

I feel really good about the $6000.00 or so I have invested in my 5' X 10' table. It will have paid for itself within 6 months or so.

All the attention you have paid to detail will pay off down the road too. I also went to great lengths to bolt in key parts so repair of rails & other wearing parts will be speedy & not to expensive. I lost count somewhere along the way of just how many hundred 5-40, 3 mm, 6-32, 12 mm, 1/4", 3/8", 1/2', & even some 3/4" holes I drilled for & tapped.

I also built my table to be taken apart in key areas so expansion is an option without having to start from scratch again.

[ajclay]

Thanks Millman52 for the support. It's been a long row to howe. I've just keep on working knowing there are only just so many parts to make.

Aj

[millman52]

Originally Posted by ajclay Thanks Millman52 for the support. It's been a long row to howe. I've just keep on working knowing there are only just so many parts to make. Aj

I went through a 5-6 month burn out stage on my build. Spring time rolled around in '07. decided it was time for the grandaughter & I to go fishing!!

I was using mine this evening & posted a few short videos of it cutting. I still need to build belt guards & soon as the weather breaks here I want to apply some paint. That should help minimise the "Home Built" looks a bit.

If I may ask what made you decide to go with servo power?

[ajclay]

The motors were something that was a bit of a mystery. It’s something no one wants to give a straight answer on. So, I just went with what a few guys in the business were using. The way I look at it, if the motors don’t work out, I’ll put them on e-bay and get a different kind / size. I just had to start somewhere. Thanks, Aj

[millman52]

I used steppers for the simplicity of use. I'm not knocking servos. Just requires encoders & from what I have read can be more troublesome with RF noise from other electronic devices (Plasma mainly). I was just curious. Servo vs. stepper there seems to be lots of debate on the issue. Definitely NOT what I want to start here. I'm pretty much of the opinion, if it works for you & you like it Great.

Keep up the good work! & keep us posted of progress. You'll love it when it all comes together as a working machine. When customers see mine working they can't believe I built it.

[ajclay]

Well I finally got to the electrical componets. I'm not 100% finished with the steel work but I'm to the point of making things move on their own before I can do the final touches. Is there someone that's real sharp on building power supplies? That's my next phase of the project to research. I'm a little behind in brain power in that dept. Thanks, Aj

[drafterman]

Great looking machine. I have noticed many machines that don't entirely lock the gantry down...I noticed in your thread description it said "router". Is the thought that the gantry will be heavy enough that it would never attempt to lift off of the rail(s) during a plunge cut?