PIC Programing / Design

Page 1 of 9 1234 ... LastLast
Threads 1 to 20 of 163

Forum: PIC Programing / Design

Discuss programing of PIC chips here and design of electronics using PIC chips.

  1. Need Help!- 16F84 7 segment display

    Started by Razer‎, 05-27-2009 08:47 AM
    • Replies: 8
    • Views: 3,909
    06-10-2009, 12:27 PM Go to last post
  2. 20Mhz crystals

    Started by PsyKotyk‎, 09-14-2006 09:41 AM
    20mhz, als, crystals, drow, mos, next, osc2, realm
    • Replies: 9
    • Views: 2,997
    11-08-2006, 08:51 PM Go to last post
  3. 3 AXIS PIC STEP

    Started by wtxrcdog‎, 06-14-2008 11:33 PM
    not
    • Replies: 19
    • Views: 7,625
    12-01-2008, 11:18 PM Go to last post
  4. 3 axis stepper motor driver using a single PIC

    Started by david90‎, 12-08-2007 08:57 PM
    als
    • Replies: 5
    • Views: 13,883
    04-05-2008, 10:22 PM Go to last post
  5. 32Khz crystal problem!

    Started by Al_The_Man‎, 09-07-2010 04:38 PM
    2 Pages
    1 2
    another, look
    • Replies: 23
    • Views: 6,619
    04-18-2011, 12:24 PM Go to last post
  6. Moved: Allen Bradley 1771

    Started by macgeek10‎, 09-01-2006 12:22 AM
    1771, allen, bradley
    •  
    •  
  7. Newbie- Almost total ignorance

    Started by DALEK‎, 07-27-2009 06:43 AM
    almost, not, took
    • Replies: 14
    • Views: 3,587
    08-07-2009, 08:19 PM Go to last post
  8. Another Lini Hack, some Qs

    Started by wayneosdias‎, 08-21-2010 12:15 AM
    • Replies: 19
    • Views: 4,570
    09-01-2010, 11:11 AM Go to last post
  9. Another PIC controller

    Started by spalm‎, 05-29-2006 10:30 PM
    4 Pages
    1 2 3 4
    • Replies: 72
    • Views: 32,658
    09-15-2012, 06:08 AM Go to last post
  10. any pic experts?

    Started by posix‎, 06-07-2005 09:44 AM
    2 Pages
    1 2
    • Replies: 27
    • Views: 7,107
    07-01-2005, 03:27 AM Go to last post
  11. ANy sucesseful xyz+spindle pic-based lpt drives?

    Started by podolskiy‎, 05-17-2010 12:07 PM
    • Replies: 17
    • Views: 8,996
    05-17-2013, 07:06 PM Go to last post
  12. Anybody build a pendant/control panel with a PIC ?

    Started by per.e‎, 07-25-2007 08:01 AM
    • Replies: 1
    • Views: 2,900
    05-10-2009, 10:27 PM Go to last post
  13. Automation Controller Board Help!

    Started by Cartierusm‎, 10-13-2008 10:25 PM
    not, said, then
    • Replies: 6
    • Views: 2,015
    10-19-2008, 08:01 PM Go to last post
  14. Best ICD2 clone?

    Started by ConKbot of Doom‎, 02-23-2007 07:19 PM
    • Replies: 4
    • Views: 10,847
    08-06-2008, 03:52 PM Go to last post
  15. BS2+Seperate Bipolar Driver Board

    Started by frank02189‎, 08-27-2006 07:26 PM
    50ma, bipolar, board, bs2, driver, stepper
    • Replies: 2
    • Views: 3,981
    12-12-2006, 07:55 PM Go to last post
  16. can i make dc servo controller with pic 18f ?

    Started by rashdan‎, 04-21-2012 02:47 PM
    • Replies: 2
    • Views: 2,838
    08-14-2012, 11:36 PM Go to last post
  17. Central point for Picmicro app note code

    Started by Al_The_Man‎, 09-24-2012 02:07 PM
    • Replies: 3
    • Views: 1,879
    09-24-2012, 04:12 PM Go to last post
  18. cnc controlled by a basic stamp.

    Started by tripolitis‎, 01-30-2008 04:52 PM
    • Replies: 6
    • Views: 5,844
    06-02-2009, 06:03 PM Go to last post
  19. Question CNC Controller PIC 16F877 - From Brasil

    Started by elizeu‎, 02-21-2005 10:16 AM
    • Replies: 13
    • Views: 35,843
    07-28-2012, 12:21 PM Go to last post
  20. Comparing two CNC usb PIC based DIY solutions

    Started by PaulMakesThings‎, 03-02-2010 04:07 PM
    down, isnt, its, not
    • Replies: 13
    • Views: 26,268
    03-09-2010, 03:55 AM Go to last post

Page 1 of 9 1234 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 5 users browsing this forum. (0 members & 5 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands