PIC Programing / Design

Page 1 of 8 1234 ... LastLast
Threads 1 to 20 of 160

Forum: PIC Programing / Design

Discuss programing of PIC chips here and design of electronics using PIC chips.

  1. PIC18f66J94 Compilation Error

    Started by olaf123‎, 11-29-2016 03:15 AM
    compiler, control/input/test.x, directory, e/knsingh/lube, make
    • Replies: 0
    • Views: 623
    11-29-2016, 03:15 AM Go to last post
  2. diy pic16f88 cnc servo motor drive 32 bit pid

    Started by ahsameh‎, 07-03-2016 08:32 PM
    2 Pages
    1 2
    • Replies: 13
    • Views: 2,084
    10-16-2016, 01:52 PM Go to last post
  3. Post Need Help!- Need help with PICBasic Pro Coding

    Started by khalidworks‎, 04-17-2016 09:43 AM
    cnc, code, pic, pro, programming
    • Replies: 0
    • Views: 798
    04-17-2016, 09:43 AM Go to last post
  4. Need Help!- PWM circuits

    Started by aluplastvz2013‎, 01-02-2016 05:38 PM
    • Replies: 2
    • Views: 1,259
    03-06-2016, 10:38 PM Go to last post
  5. Question Need Help!- parameters procedure of Mitsubishi M0 control

    Started by braided‎, 12-20-2015 04:26 PM
    cnc, control, mitsubishi, parameters, procedure
    • Replies: 0
    • Views: 706
    12-20-2015, 04:26 PM Go to last post
  6. Rotary Table Controller debugging.

    Started by Driller2‎, 12-20-2015 01:32 AM
    • Replies: 0
    • Views: 615
    12-20-2015, 01:32 AM Go to last post
  7. RT-8p8c - PIC32 based ethernet interface board for LinuxCNC

    Started by kinsa‎, 10-19-2012 07:21 AM
    2 Pages
    1 2
    • Replies: 16
    • Views: 8,707
    10-30-2015, 08:44 AM Go to last post
  8. Stand alone rotary table indexer.

    Started by kwackers‎, 11-15-2007 04:52 PM
    • Replies: 11
    • Views: 5,501
    10-09-2015, 11:02 PM Go to last post
    • Replies: 5
    • Views: 1,542
    05-27-2015, 11:14 PM Go to last post
  9. Build Thread- Sense Step on Stepper ?

    Started by vangalvin‎, 04-22-2015 04:29 PM
    calculation, pick, sense, step, stepper
    • Replies: 4
    • Views: 988
    04-22-2015, 06:22 PM Go to last post
  10. isolated DAC. PWM ( 20khz ) to analog 0-10Volt

    Started by visky‎, 07-29-2014 01:31 PM
    • Replies: 1
    • Views: 3,106
    10-11-2014, 09:29 PM Go to last post
  11. PIC based DRO

    Started by BillTodd‎, 08-11-2008 04:42 PM
    10 Pages
    1 2 3 4 5 ... 10
    • Replies: 112
    • Views: 49,902
    04-08-2014, 10:38 AM Go to last post
  12. Need Help!- DRO Design discrepancies.

    Started by ayeff‎, 01-01-2014 01:40 PM
    • Replies: 1
    • Views: 1,271
    04-08-2014, 10:34 AM Go to last post
  13. Question Need Help!- elm chan dc servo controller

    Started by visky‎, 01-28-2014 11:06 AM
    • Replies: 0
    • Views: 1,736
    01-28-2014, 11:06 AM Go to last post
  14. Want to get into pic programming.

    Started by 109jb‎, 05-19-2013 07:59 PM
    • Replies: 4
    • Views: 2,250
    07-29-2013, 12:37 PM Go to last post
  15. Question Build Thread- PIC/Parallel port CNC driver code

    Started by faacuunndoo‎, 06-02-2013 01:59 AM
    down, goes, maybe, then
    • Replies: 7
    • Views: 2,446
    07-29-2013, 12:20 PM Go to last post
  16. USART on 18F?

    Started by Al_The_Man‎, 05-18-2013 02:52 PM
    • Replies: 2
    • Views: 1,360
    05-19-2013, 07:13 PM Go to last post
  17. ANy sucesseful xyz+spindle pic-based lpt drives?

    Started by podolskiy‎, 05-17-2010 12:07 PM
    2 Pages
    1 2
    • Replies: 17
    • Views: 5,298
    05-17-2013, 07:06 PM Go to last post
  18. Exclamation PC Base DRO

    Started by aadityadengle‎, 02-02-2012 09:55 AM
    2 Pages
    1 2
    • Replies: 22
    • Views: 6,220
    03-25-2013, 11:09 AM Go to last post
  19. More than one clock from the PIC to drive L297

    Started by JosipMiller‎, 02-26-2013 12:49 PM
    als
    • Replies: 4
    • Views: 1,949
    03-03-2013, 06:31 PM Go to last post

Page 1 of 8 1234 ... LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 2 users browsing this forum. (0 members & 2 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 500 views
Hot thread with unread posts
More than 25 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


About CNCzone.com

    We are the largest and most active discussion forum for manufacturing industry. The site is 100% free to join and use, so join today!

Follow us on


Our Brands