| | |
Regards.
Good I say to them am Chilean and a time ago behind I saw a machine cnc industrial, and at the time I have tried to see like to design my own cnc but housekeeper, have sought in the Internet and I found his page and by much that I dress still I am lost by the matter, he would be grateful for the help of everything those who already handle the matter to be capable of constructing my machine cnc who would be the first one in chile since for here they do not handle for anything the topic, good they all are welcome with his ideas and help.
Which is the idea of cnc to constructing.
1 º that the area of royal is of 32 " for the axis X, 24 " axis Y, 4 " axis z (material expresor).
2 º that the structure is firm.
3 º that the cost of the machine is not very expensive.
4 º that could work wood, plastic, alumnio, recina, silicone.
After consulting sending e-mail, visiting shops and calling for telephone, my result on material has been the following one:
Profiles of alumnio, seal 32, controllers or cards, there is no the material bony one not exite, I sit it but for my country the creativity is not valued and projects like the domestic cnc always stay in an alone idea.
But I am decide to carrying out it and of insurance that with his help it will be possible.
Of profile of alumnio there is one that is like 8020, but of 2,36 "x1,18 and one that it is cudrado of 1,57 "x1,57".
The nema 32 I can encontralos in Argentine it is the most nearby thing.
What is screws, rails, bearings of it is here in chile
They can help me with the measures to arm the estrcutura, using the type of profile alumnio that here exists, 30x30, 30x60 and 40x40mm
Since I attach an image?
Welcome to the zone, Ramadihel. I'm sure people here will help you on your build.
To attach an image, go down to the "Additional Options" when you're postiing and click the "Management Attachments" button.
Given that your machine is not very big, why nema 32? I use nema 23 for my 4' X 8' machine and they work just fiine.Originally Posted by ramadihel
jsantos, sorry but I do not drive as though the issue was not sure what kind of NEMA should consider now if your doctor a NEMA 23 motor works well, then that engine considers a question "for the 3 axes should consider the same type of engine or not?
here are some profiles there is only 30x30, 40x40 and 30x60, so the whole structure should I make with that material, is it possible this page?
and I leave an image of cnc I design or in which I wish to base, but I have only the image, so your help will be coming good
Nice looking machine. I can't tell if the aluminum extrusion is metric or imperial. But given your choices, I would go with the 30X60 and build the frame exactly the way it's shown on your picture.
You do not have to have the same type of motors for all 3 axes. Some people use a single Nema 32 for their X and use Nema 23 for their Y and Z.
I used nema 23 for all my axes.
Using a nema 23 will allow you to use the gecko g540 controller so you don't have to build your own controller. However, I don't know if the gecko g540 controller is available in Chile or if you can order it from here in the U.S.
Well, today I found a place that has the NEMA 23 motors, now I give the details for me to indicate which best fits me.
NEMA 23 0.6 Nm
NEMA 23 1.1 Nm
NEMA 23 1.8 Nm
NEMA 23 2.8 Nm
jsantos which would be more appropriate.?
I consulted gecko G540 but I have not had any luck.
Posting Permissions
| | |
LinkBack URL
About LinkBacks
